Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Replaces the latching spring pin on your Yakima bike carrier. Works with HoldUp (Y02443, Y02443-2, or Y02445), TwoTimer (Y02468 or Y02468-FB), or FourTimer (Y02469 or Y02469-FB) bike racks manufactured after 2016.
Features:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi everyone, it's Evangeline here at etrailer, and today, we're taking a look at our Replacement Latching Spring Pin for your Yakima bike racks right here at etrailer. So I have this here on our Yakima HoldUp bike rack, but this will also work on some of your other Yakima bike racks like the TwoTimer or the FourTimer. Now, this will also depend on what year your bike rack was made, for example, if you had the gray Yakima HoldUp, which is the older iteration, you would use a different spring pin, so this is gonna be for your newer Yakima HoldUp bike racks, check out the product page just to verify which bike rack you have. So on this side, I have the newer lashing spring pin, and on this other side, I have the older spring pin from an older bike rack. So you can see how you can definitely upgrade or replace your old hardware, whether you cross threaded the old spring pin or maybe broke off the plastic pieces, this is an exact replacement and works the exact same way. So this spring pin fits right into your bike rack and allows you to press on it and then pull it out, and this will be used in order to tilt down your bike rack or fold it up.
So this is definitely an upgrade from the previous version to the spring pin for the older bike racks, because those we're just a spring pin and they didn't have a safety latch. Now, the safety latch is a little tricky to use sometimes, 'cause you have to press it in and pull it out, and make sure you don't pinch your skin between that latch, so just something to think about as you use it. Notice how it is shaped like a round bolt, but you have these flat edges, so that's gonna be so you can use your 24 millimeter wrench, it fits perfectly into the wrench and allows you to tighten or loosen the ball onto your shank. If you need to replace yours, and if it's still attached to your bike rack, just use your 24 millimeter wrench in order to loosen it off of your shank. Just set this up.
Once you have that out, you can then replace it with your new part. So the easiest way to put this back in is just to lift that bolt out of the way, just line up your threads and then start turning. Once you have it threaded through, you can then use your wrench to tighten it down. So I did this by just changing out our latching spring pin, but really, the easiest way to do this is if you take off the spine by removing this bolt, that way you're only threading it onto the shank, and then you put the spine back on afterwards, but it's really up to you, all in all, it's still very possible no matter how you do it, it might just take a little bit more effort. So just make sure that's tightened down with your wrench, and that's it for the install.
Now, if you did cross thread the inside of your shank and not just the latching pin, you may need to replace the shank itself, so just check that out here at etrailer, because you can get the shank with the spring pin included if needed. And that was a look here at our Replacement Latching Spring Pin for your Yakima bike racks right here at etrailer..
Customer Satisfaction Score:
97% were satisfied with this product
3% of customers were not satisfied
Ratings & Reviews
Christopher H.
8/4/2026
Thanks for the kind words about our service, and I'm sorry to hear the replacement part didn't hold up. We appreciate you sticking with us, and hopefully these replacements get you back on the road.
Colleen
11/3/2025
Well not a year, but a few days and this was a real simple install for even someone who might be 70 yrs old! Im back to biking..thank you.
Jim
8/25/2025
After multiple uses this past year, the spring pin continues to work flawlessly!
Jenny N.
8/31/2023
I hate to hear that the pin did not work for you. I want to see if I can help find the right one. What model of bike rack do you have? How old is your rack?
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Ronk
9/8/2025
Still working great, and as intended.