Summer Starts Here - Save up to 70%
# 1
Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad - 4-Point Set
The system is not what was advertised, it's better, at least for me. Everything arrived on a pallet in excellent condition, except for the advertised remote. I contacted etrailer and they put a replacement on order which I received a few days later. In the meantime, I tried to place the controller in the mode to sync the remote and see if the remote I had with my RV would sync, but I could not get the controller in that mode to accept a remote. Upon reading the controller label, I noticed it said BT and had a passcode on the side of it, so I downloaded the app and it connected to my phone. It seems the LCI Linc remote is obsolete for my Ground Control 3.0 and it is now using the phone app. Everything seems to work as expected; I'm excited to try everything out this weekend on our first outing. I was able to push a fiberglass push stick from the front basement to where the rear jacks are located without dropping the underbelly and pull all the required cables to the rear of the camper and utilize existing frame holes to bring the connectors out to the rear jacks. I think this will be a nice upgrade to our fifth wheel after our factory landing gear failed.
shipped in a timely manner. Easy install wit good instructions. I did have one question about the location of the rear lifts and called the company and we had an answer instantly. Wiring was very easy with good instructions. The system worked on the first try and have had no issues so far. Great system. I was looking at newer campers with auto leveling and about 40 to $50,ooo if I traded my paid for camper in. The cost saved me a lot of money and works as it should and saves my back and a lot of set up time. would and have recommended to others. Thanks.
# 2
Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 6-Point Set
Let me say this to start, this system is AWESOME!! If you do not have a leveling system on your camper, this one works very , very well. I will say, the install and the learning curve takes time and is not too hard, but it's not super easy either. Once I got the system in place, and understood how to use it, the rest was a piece of cake. Take your time on the install and get help. The parts are robust and heavy, so two people make it much easier. Have sharp drill bits to drill the attachment holes. Wiring is super simple, but take your time and make sure you get all the connections good and tight and secured well with zip ties. The system requires a good strong battery, so make sure your battery is in great shape and you will not have any issues. Get the Lippert app also, it is very helpful. I love it now, when I pull my 2006 Keystone Raptor 5th wheel toy hauler into a campsite, I hit a couple buttons and the longest it has taken to level my unit is 2 minutes and 30 seconds. I love it! It puts the camper at the same level every single time, which is awesome. No guessing, no driving up and down on blocks, just push a button and walk away until the camper is perfect. Would I do this over again you ask? Absolutely. Awesome system!
After the initial installation there was a little confusion about setup I have been very happy with the way it works really simple push one button hit auto levels it's still working well thanks
# 3
Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System - 10,000 lbs
One small part was missing from my Ground Control TT. Carol Korren expedited delivery of the missing part and the UPS truck pulled up at the moment I needed the part. Fantastic customer service!
We love our one touch jack system. We used in on a 3 month camping trip out west setting up probably 40 plus times and we continue to use our camper and the jacks work great!
# 4
Ultra-Fab Ultra Scissor Jacks - 24" Lift - 13,000 lbs - Qty 2
Definitely a heavier duty version of our campers stock stabilizers. They bolted right up to the brackets and glad we have new stabilizers. I hope the paint lasts on these as that seems to be an issue with the other, cheaper stabilizers. Time will tell.
Straight forward drop in replacement for the old worn out jacks that came with my trailer. Mounting flange and holes were identical in size and location. These were about 3/4" longer than the old jacks but that wasn't enough to cause an issue. The best thing about these is that they are much sturdier than the old, cheap jacks Forrest River installed at the factory. The scissor legs are wider and the screw is larger with finer threads. Possibly overkill for my single axel trailer that weighs at most 6,000lbs fully loaded but the price was right so I bought 4 of them. The only CON is that the screws were not straight right out of the box. I don't think this will cause an issue for normal operation but I was a bit surprised to see the whole scissor assembly wobble when lowering and raising them.
# 5
Lippert Power Stance Electric Trailer Jack w/ 7-Way Plug - A-Frame - 18" Lift - 3,500 lbs
The alternate power setup makes its slow rate of rise necessary which would be good if my lithium batteries went low. To avoid battery problems be sure to add an inline battery disconnect from the trailer power when using tow vehicle power. I simple added an inline fuse that could be removed should I need to use the tow vehicle power.
I was amazed at how quickly my replacement from etrailer arrived. I was a bit worried that the installation of my new jack would be more difficult that I expected. The reverse proved to be the case, it was very simple to place the trailer tongue on jack stands, remove the old jack and install the new one. As the old saying goes "even a cave man could do it."
# 6
Ultra-Fab Electric A-Frame Jack w/ 7-Way Plug - 18" Lift - 3,500 lbs
I've had this power jack for about a year and it works flawlessly, it beats hand cranking. And not to mention the great service from etrailer their the best in the business.
Bought Pro Series Weight Dist Hitch, Jameson C was very helpful picking the right one out , ordered it on Friday and it arrived on Wednesday a day earlier than expected. Placed a second order for an electric jack and misc. parts. Extremely happy with their service. I don't review stuff but these guys deserve one.
# 7
Leveling Scissor Jack Set - 24" Lift - 10,000 lbs - QTY 2
Quality product w/ quick delivery
Received shipment next day after ordering...no added charges. Shipping package arrived in excellent condition. Scissor jacks look good and work smoothly.
# 8
Lippert High-Speed Power Stabilizer Jack - Black Waterproof Switch Kit - 30" Lift
Good thing stabilizer was easy to install because there were no directions included. Item was delivered quickly. I received item within a week.
Box is damaged and tape all over with clear tape holding box closed and first thought is missing parts and paper work and instructions to install ! Pictures taken and open up box finding all parts inside except for the paper work instructions to install, also the rubber cover for the water poof motor is damaged also!
# 9
Ultra-Fab Ultra Scissor Jacks - 30" Lift - 13,000 lbs - Qty 2
Didn’t last 3 months the end came off and screw mess up where the jack don’t work anymore
Worked beautifully for a Replacement for our customer
# 10
Lippert High-Speed Power Stabilizer Jack - White Switch Kit - 30" Lift
Easy to install and functioned perfectly. Customer has been utilizing it for a year and still raves about it. Thank you
Pros: Works better than I anticipated. Looks great and has better ground clearance than the stock scissor-jack stabilizers. Cons: Installation instructions/documentation weak or non-existent. If all of the instructions, wiring diagrams and documentation were in one place on the web page under a separate tab rather than having to dig through the reviews and the Q & A’s, I would have given this a 5 star rating. I ordered the LCI Power Stabilizer Jacks with the white switch Kit (LC369774) because I wanted the switches mounted in the camper wall so they would be better protected than if they were mounted in the flimsy fender skirts of my camper. I also needed the bolt-on spacer kit (LC673594) for both the front and rear jacks to clear a propane line that runs along the length of the frame. Installation was relatively easy, although there are NO instructions on how to install the spacers kits; the video on etrailer.com was no help whatsoever with the installation. I bolted the jack mount brackets to the shorter side of the spacers using carriage bolts and flange nuts; the slotted holes in the spacers accepted the carriage bolts, aligned perfectly with the holes in the jack mounts, and allowed me to install them without having to try to fit a wrench inside. Then it was just a matter of drilling holes in the frame at the appropriate spacing for flange bolts/nuts through the slotted holes on the end of spacers. I was very pleased with how the switches and the switch compartments looked once installed. Again, though, it took lots of digging to find the wiring diagram and then the matrix for the switch wire colors, because the wires on the white switch are colored differently than the black switch that all of the diagrams show. Also, it states on the jack installation instruction sheet that the power must be a minimum of 10 gauge wire (AWG-10), but nowhere on the wiring diagram does it say anything about that. AWG-10 is a MUST because of the way current drops over a distance. In the case of my camper, it is a 30 foot run which requires that gauge of wire for 20 AMPs.
# 11
Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 23" Lift - 5,000 lbs - Black
I was extremely impressed with the recent technical and customer support from etrailer. Over the weekend, they answered my questions to select the appropriate replacement electric jack for my Airstream. Also, when there was a shipping delay (not etrailer’s fault), Rose provided prompt responses and professional support. I will continue to use etrailer for my RV needs.
Definitely has the power I need however I can't open my tailgate when my camper is hooked up. 5 stars for power.
# 12
Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs - Black
Replaced stock Air Stream power jack which started making grinding noises. New 4,000 pound jack easy install and works fine. Using it to lift 25ft trailer and 2500hd Silverado to attach anti-sway bars. Had to mount it sideways due to propane tank cover, but it works great. Had one of these on a larger trailer that a hurricane destroyed. Nice unit and easy install.
Overall the product does exactly what it's intended for and works well. I however assumed that this would be a simple R&R for my camper and did very little installation research other that the video provided on etrailer' s website Sadly it did not fit. Not at all. I didn't take into account that have a double framed hitch toyhauler. The baseplate on the factory leg was a TRIANGLE.....this unit was ROUND. Also the primary shaft was thicker than stock and would not drop down into place I know modifying is frowned upon, but I found that ALL powered hitch legs I found have round mounting plates and it's not mentioned the leg tube is thicker than OEM? Since NOT having a power lift wasn't an option for this camper application...too heavy in the front when ATVS loaded to lift for setting the equalizer hitch tension bars, I proceeded to modify by cutting the rear rounded mounting base ... square. Took off about 1/2 inch. Then I took my metal Dremel sanding bit and increased the hitch leg hole diameter slightly. Took about 1 hr. Dropped it in. Wired it. Tested it. All good. If you can't post this I understand, but take note that some of your website descriptions may need to be enhanced. Thanks!
# 13
MORryde 5th Wheel Cross Brace Landing Gear Stabilizer
I ordered the MoRyde 5th wheel cross brace to stop the shaking in our 26' Winnebago Micro Minnie. The brace was easy to install and does a great job of stopping the trailer shaking; I don't even need to twist it tight. The downside is that it was too long to fit between my jacks so I had to take it to a machine shop and pay them to shorten each brace by 6".
The cross brace worked great. It took the shake out of camper. Would highly recommend them. Installation was easy. Thanks for a great product.
# 14
Lippert Scissor Stabilizer Jacks with Handle - 30" Lift - 10,000 lbs - Qty 2
Deception in advertisin It may be my fault for not reading to total description in detail rather than glancing over it. Similar products from other companies list the weight capacity as each but this product lists the 10,000 pound weight capacity as both. They are only good for 5000 each. The [online] option was at least 6000 pounds! The only reason they were not returned is the 30in capability.
These worked out great easy to install with the circular mounting plate.
# 15
Electric Jack w/ Footplate - Drop Leg - A-Frame - 25-1/8" Lift - 3,500 lbs - White
Item arrived a day earlier & in good condition! & was a very easy install ,& is a upgrade from manual one that broke at the handle ,& this is a upgrade for my 2008 22'Airstream Safari! Can't wait for my next outing, Also I like that it comes with a backup manual hand crank in case you need it,& that it was a exact fit for my travel trailer,It's a complete package that needs nothing else.
I purchased this jack to replace my tired 10 year old camper jack . I ordered it at 10:00 AM Monday and as promised by Ian it was at my doorstep on Friday just in time for my weekend getaway . Installation was a breeze . I gave the product a 4 out of 5 for a few reasons . First , I was not able to see the manufacturer of the jack before receiving it . Which made name brand comparison pricing difficult . However I feel pricing was on target . Second , I feel that the jack should come with a battery terminal end connector and new mounting bolts with the hardware that was included . This didn’t pose any difficulty to me as I had hardware at hand but for some it will mean a trip or two to the hardware store . Third , once installed , at least with my truck and trailer , unless the truck and trailer are perfectly aligned and level the jack motor gets in the way of opening the tail gate . On first use I noticed it was much slower than my original but the strength made up for it . This jack had no difficulty or hesitation lifting my truck and trailer for load distribution and anti sway bar installation . I would recommend etrailer and this product . Time will be the final test of its durability .
# 16
Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors - 30" Lift - 6,000 lbs
Finally got around to installing my PT II Stabilizers 30" front and rear of our 26' Surveyor. Pre - assembled them to make sure they went together ok. Luckily I had two sources for power front & rear which made wiring easy, I used a Buss block to make all positive connections, grounds straight to frame, soldered all connections and heat srinked to seal. Using the 3/8" self tappers was fun.Well got it all together and all works well makes trailer very stable, don't have to worry about scissor jacks collapsing anymore.
It looks like a great product am anxious to install them. I have a symbol of them in my garage and I have one with a really crooked foot. The bolt hole on the retracting arm was drilled in the wrong place so it is totally crooked, not a deal breaker though. I’m sure the are more than Adequate
# 17
Bulldog Tandem Landing Gear Set - Drop Leg - 36" Lift - 8,000 lbs
Delivery was on time, but the box it arrived in didn’t fair we’ll and parts were hanging out of the box! But everything was accounted for and the parts were well wrapped. Installation was very easy. The only issue was the locking pins mount plate is tack welded to the primary leg that the motor moves up and down. Those mounting plates had to be removed to install the lead and follow jacks. A grinder made short work of that. I didn’t put the mounting plates back on, instead I used my spring loaded pins that were on the old legs, they were still in good working condition. Also I didn’t use the adjustable cross over rod that came in the package . I opted to use the one that was on my old jacks, it was constructed of heaven gauge tubing and didn’t have a much (slop) movement in it. Also did not use the plastic housing gear box, I purchased a aluminum house gear box from e-trailer a few months back and used that one keeping the plastic for a spare. Very satisfied.
The leg pin came out because of the design, it is not a strong locking mechanism to not pull it all the way out. (My wife pulled it all the way out) Afyer furthet inspection, in addition to poor locking mechanism, the size of the pin is not adequate for the specified weight of the jack.
# 18
Stallion Stabilizer Jacks - 7" Drop Leg Travel - 22-1/4" - Qty 2
I mounted this Stabilizers Jacks to the back of a 4x8 utility trailer. I use the trailer to haul my Honda ATV to MotoAmerica motorcycle races. Once the ATV is removed I lower the jacks and mount my tent inside the trailer. These stabilizers allow me to safely move around in the tent without fear of the trailer tipping.
Jacks worked great. Added them to an aluminum 2 place enclosed snowmobile trailer that did NOT like humans to walk up the rear ramp when unhooked and empty!? ...problem solved.
What our customers are saying:
"WOW! I am impressed! I called to place my order and real person answered, spoke perfect English, albeit a slight southern accent, and my order was sent within a day, shipped quickly and I had it a few days later. I saved over a hundred dollars over local and installed it my self. I cant imagine how that they could do any better. THANKS!"