# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Exactly as etrailer described it on their site. One Drawtite 2923 ballmount. It is a superiorly made product which I have used for hauling my boat around the USA and Canada for many years. I decided to buy a second one so when friends and family borrow one of my trailers I need not take mine off my Pathfinder. etrailer prices were excellent and their shipping very fair priced and quick. I will not hesitate to buy all my trailering needs from them.
I was very happy with the product and the service.
# 2
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
Complete hitch, nothing missing, no chips in paint or damage. Was well wrapped for shipping.
ETRAILER PRODUCTS ARE THE BEST.
# 3
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
# 4
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Good fit, well made, worked well on first use, ball attached easily, was the reciever I was looking for.
Exactly as etrailer described it on their site. One Drawtite 2923 ballmount. It is a superiorly made product which I have used for hauling my boat around the USA and Canada for many years. I decided to buy a second one so when friends and family borrow one of my trailers I need not take mine off my Pathfinder. etrailer prices were excellent and their shipping very fair priced and quick. I will not hesitate to buy all my trailering needs from them.
# 5
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
The ball mount was a complete failure even after a lengthy discussion on the phone. I wanted a ball mount that would accept the rocker ball and anti-sway bar. The bar sent to me can't be used this way. An email and phone message to the sales person I ordered with, got no response.
# 6
Curt Multi-Ball Adjustable Ball Mount for 2" Trailer Hitches
Picked up my teardrop in ABQ on 2/17/23, and the Curt ball mount lined up perfectly with no drop/rise, and the extra length gave clearance for my rear door mounted spare tire. This mount is a beast, and the "overbuilt" nature of it gave me confidence that my Bronco would tow the teardrop easily. I also got the Curt Echo wireless brake controller, which synced easily to my phone and was easy to install, set up, and use. Overall a great towing experience, thanks to etrailer and Curt!
Very versatile - can use it on both my vehicles that have very different hitch height. Clean welds, super solid. Weighs a LOT!
# 7
Flash Secure Adjustable 2-Ball Mount w Chrome Balls - 2" Hitch - 6" Drop, 7" Rise
Very strong, easy to install and very secure. Yes a bit pricey, but well worth the money. I did notice there was what I thought was an unusual amount of play in the receiver. I called etrailer and Marcia was so very helpful and very concerned that I may have received the wrong product. She even called the manufacturer and found out what the changes that were made by the manufacturer which made the pictures incorrect. My hat is off to Marcia and all the folks at etrailer
ball mount fits loosely in the receiver so that the pins that extend out from the ball mount shaft through the holes in the receiver don't extend out far enough, for my liking. This is because since the ball mount shaft has so much play, it will shift to one side. Then, the pin on the other side does not extend all the way out of the hole so that it is not flush. True, i am being paranoid. However, i imagine a case like a crash where enough force could pull the shaft out from the not fully extended pin side to release the trailer to wreak more damage. I would just feel more secure if the pins went out further through the receiver or the shaft was not so loose. Otherwise, i really like the product a lot... enough to give it four stars... :o)
# 8
Drawbar for 1-1/4" Hitch - 2-5/8" Rise, 3-1/4" Drop - 7-3/16" Long - 3.5K
The hitch works great. The service was excellent!!! I'm going back and having a hitch put on my other car soon. Thank you.
Everything was perfect.! Nice paint, package, and fast shipping.! Im satisfied.!
# 9
Draw-Tite Ball Mount - 4-3/4" Rise, 6" Drop - 10-1/4" Long - 6,000 lbs
Good fit, well made, worked well on first use, ball attached easily, was the reciever I was looking for.
Exactly as etrailer described it on their site. One Drawtite 2923 ballmount. It is a superiorly made product which I have used for hauling my boat around the USA and Canada for many years. I decided to buy a second one so when friends and family borrow one of my trailers I need not take mine off my Pathfinder. etrailer prices were excellent and their shipping very fair priced and quick. I will not hesitate to buy all my trailering needs from them.
# 10
Flash Secure 2-Ball Mount w/ Chrome Balls - 2" Hitch - 4" Drop, 5" Rise
Love the design with no locking through pins to worry about. Only reason for three stars is I received the product with cosmetic damage from being dropped.
Works great. The locking pin feels like it could be a bit wider but otherwise I love it. I’m a novice at towing so the adjustability of the height has helped make sure the towing has been optimized at all times.
# 11
Flash Simple 2-Ball Mount w Chrome Balls - 2" Hitch - 6" Drop, 7" Rise
Works great. With all the adjustments we can get our trailers to haul level now. Quality looks really good and it has the 2 size trailer hitch balls which makes it way more convenient.
VERY HAPPY, BUT STARTED TO SEE SOME RUST ON THE HITCH BALL AND ONLY USED TWO TIMES. THE VERSABILITY OF THE PRODUCT IS GREAT. OTHER THAN THE SMALL AMOUNT OF RUST ON THE BALL ITSELF, IM VERY SATISFY AND WILL BUY FOR MY OTHER TRUCKS.
# 12
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
This was the longest hitch ball mount I could find anywhere. I used it with a short extension for my 2021 T G so that I could open the back doors without hitting the trailer wheel crank. With my new trailer, Intact Flyer Discover, I don't need the extension and can still open the doors. Works well.
# 13
Rapid Hitch Adjustable Aluminum Ball Mount Kit - 2 Zinc Balls - 5-1/2" Drop, 6-1/2" Rise
Sooooo....you sent me a product that was somehow put together backwards and I cannot take them apart somehow the ballhitch is stuck on the male portion backwards and defies gravity and doesn’t need a pin to stay on(becaue thier is no where to put the pin in cause it’s backwards
Have done about 5k with this hitch, just once with a 4500lb camper but mostly with a 3000lb cargo trailer. The former in a highly raised position and the latter in the absolute bottom position. The hitch has worn very well and shows no signs of excess wear, save for the surface of the 2" ball, but it's not concerning. On a Jeep Grand Cherokee with a stock suspension, this seems to give the right balance of range of adjustment without dropping so low in the lower configuration as to scrape through dips, though it can still be done on very sharp dips with the hitch on the lowest setting. Overall, very pleased with it and love that it's lighter than steel and won't rust.
# 14
Convert-A-Ball Ball Mount for 2" Hitches - 6-3/4" Rise, 8" Drop - 10,000 lbs
This ball mount is a beast. It may be a little overkill for my little trailer, but better safe than sorry. Hooking a small camper to a Nissan Pathfinder required an 8" drop and this fit the bill perfectly. Extremely sturdy unit and the shipping was fast. Ordered it Friday and received it the following Tuesday. Not impressive until you add the fact that I'm In Calgary AB and it came from MO. That's fast. I've ordered many things from etrailer and the service has always been exceptional.
I use this hitch when I pull my horse trailer to make the stop/start transitions as smooth as possible for the horses in the back. It works great. I also love that its a category IV hitch. Really heavy duty. My truck sits pretty high, and the amount of drop - 8" is perfect. I never worry about hitch failure travelling with my horses - they're a heavy load, and any failure would be a disaster. E Trailer provided excellent service, and their shipping to Canada was prompt and hassle free. Way to go guys, keep up the great work!
# 15
Convert-A-Ball Ball Mount for 2" Hitches - 8-3/4" Rise - 10" Drop - 8,000 lbs
This ball mount is a beast. It may be a little overkill for my little trailer, but better safe than sorry. Hooking a small camper to a Nissan Pathfinder required an 8" drop and this fit the bill perfectly. Extremely sturdy unit and the shipping was fast. Ordered it Friday and received it the following Tuesday. Not impressive until you add the fact that I'm In Calgary AB and it came from MO. That's fast. I've ordered many things from etrailer and the service has always been exceptional.
Works great. Needed the drop to tow a utility trailer at level.
# 16
EZ Heavy Duty Adjustable Hitch with Combo Ball - 8" Drop/Rise - 14,000 lbs
Just did ~500miles with about 5k worth of car plus trailer over hill and dale. Works great. No detectable wobbling, but pins are easy to get through holes (not too tight or misaligned). Heavy, but not like, completely unwieldy.
This Hitch does the job perfectly for all my trailers keeping in the upright position and did not notice any excessive rattle..
# 17
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
I have a custom made tow guard. The ball mount I have was too short to allow me to attach the tow guard to my new truck. I searched the web and found just what I needed at etrailer.com. It's the only site I found that carried the size I needed. The product fits my needs perfectly. I can now protect my boat from rocks and other road debris when towing. Thank you etrailer.com.
# 18
Curt Ball Mount - 6" Rise, 8" Drop - 11-1/2" Long - 5,000 lbs
I would have given you guys 5 stars if it were not for the way the items were packaged. The ball mount and break controller were loose in a medium sized box with out any packing in between. The box for the break controller was smashed. I don't see any visual damage on the break controller its self but, I also haven't wired it in. It would be a good idea to separate these items with some kind of packing materiel so they don't slam around in the box. Other than that the products arrived as advertised.
Complete hitch, nothing missing, no chips in paint or damage. Was well wrapped for shipping.
# 19
Curt Class III Ball Mount with 2-5/16" Ball - 2" Drop - 7,500 lbs
I would have given you guys 5 stars if it were not for the way the items were packaged. The ball mount and break controller were loose in a medium sized box with out any packing in between. The box for the break controller was smashed. I don't see any visual damage on the break controller its self but, I also haven't wired it in. It would be a good idea to separate these items with some kind of packing materiel so they don't slam around in the box. Other than that the products arrived as advertised.
Complete hitch, nothing missing, no chips in paint or damage. Was well wrapped for shipping.
# 20
Curt Class II Drawbar - 5" Rise - 11-5/8" Long - 3,500 lbs
I was in need of a hitch higher than the standard 3 or 4 inch riser and spoke with Samatha B, after a couple of emails she found a 5 inch riser for my 1 1/4" receiver. Just what I needed and a happy customer. Received very quick and good sturdy quality. Thanks again!
3.5 stars. Product looks like it should perform as advertised, but it arrived with several chips in the paint. This is most likely due to improper surface preparation and cleaning before the powder coat was applied. As you can see in the photos, there is already some surface rust on some of the areas, including the hole for the hitch pin. Ultimately the paint will get scratched up from use, but it would be nice to see some extra attention to detail from the factory.
What our customers are saying:
"Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast."