# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
I recently purchased a class III Curt hitch, mount, ball, wiring harness and hitch pin for my 2011 Toyota Rav 4. The installation was as described, straight forward and easy. The instructions were easy read and matched the vehicle I have. Everything fit together exactly with no modification needed. Shipping was directly to my door. The unit was undamaged and everything was shipped all in the same box. I have used my hitch several times, and although I an new to towing, I look forward to years of use. I did have to make a quiet clamp for the banging mount with an empty trainer, but from what I understand, this is common to all hitched.
# 2
Curt Ball Mount for 2" Hitches - 1" Rise, 2-1/4" Drop - 7-5/8" Long - 7,500 lbs
Well made and very sturdy. Quality product.
Purchased the hitch and wiring kit for my 2012 Rav4. I was going to have a garage do the installation, but then decided to do it myself. The written directions and the available videos made the installation of the wiring and the hitch a relative breeze - and I'm not particularly handy. My hitch lined up with the bolt holes perfectly and the wiring was without drama. All in all a good purchase and I was very happy dealing with etrailer. Hooked up the trailer today and all works as it should.
# 3
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
Great Product. Installation was straightforward and took about an hour. The longest part was cleaning the rust out of the weld nuts with WD-40 and the tube brush. Once they were cleaned installation was simple.
Arrived quickly and functioning perfectly
# 4
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 6-3/4" Long - 3,500 lbs
Fits perfect should work find
excellent ease of installation....
# 5
Draw-Tite Drawbar for 1-1/4" Hitches - 5/8" Rise, 1-1/4" Drop - 7" Long - 3.5K
Finished nicely and fit perfectly, except had to take a file to the inside of the receiver as the punched holes deformed the tube slightly. Now...smooth!
good product, good quality. on time delivery
# 6
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
Hitch installation went well after viewing the installation video. The wiring harness video was not completely accurate but provided more than enough visual information to perform the wiring install in a reasonable time. Overall, very happy with product at this time due to easy install due to seller videos. Haven;'t used it yet other than to take a test drive, so, sorry no videos, Etrailer provides a good product with excellent product support. Shipping was very fast and of course the price was right. I would definitely use them again.
Can't wait to get them installed and see how they fit.
# 7
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 3/4" Rise, 2" Drop - 7.5K
The equipment was top rated. I do like the lock option. The only negative I would mention is, for my vehicle, the mechanic needed to weld one side of the attaching tow bar because the dimensions didn't quite match a Toyota RAV4.
# 8
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
The etrailer.com site was easy to navigate and I found the right draw bar for my new Rav4. The order was processed very quickly and delivery was within just a few days of the order. Prices are fair and customer service was great. Thanks for a great online experience!
Received it exactly when they said it would arrive. Works great. Exactly as described.
# 9
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
I have a 2004 RAV 4 and I was trying to get my ball away from the spare tire carrier. I think I probably would have been fine with the next size (shorter) ball mount and still got the job done. The good news is that with the 2 inch drop, I can open the rear door and it just rubs the seal at the bottom of the door a little bit, but I can still easily open the door. I did not want to drop the ball any lower, So this works out well for my rig.
Very happy with this ball mount - provides just the amount of drop we required for a level tow of our GeoPro travel trailer by our RAM2500. Plus, the extra length not only allows a tighter turning radius, but also allows us to lower the truck tailgate without having to detach the trailer. Huge improvement on all accounts for us compared to our prior setup. The product is well built and I'm confident will provide us years of good use.
# 10
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
We sold our small motor home and purchased a small travel trailer. This hitch provided a perfect solution to how to use our bike rack while towing the trailer. It even allows room for the pickup tailgate to be lowered without removing the bikes from the rack. The hitch is very hefty with a high weight limit - plenty for the GVW of the trailer (7,000#) plus 125# of rack and bikes.
This has been an amazing multipurpose ball mount. We purchased this to use with our Hollywood Bike Rack and also to connect onto our boat. We weren't sure if this would work, but it was awesome. It is very well built and We had to make some minor adjustments to the position of our boat on the trailer so the turning radius of the bike rack that was attached would clear the truck. This is very well made and solid.
# 11
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
Wonderful product. I had the hitch installed in 10 minutes. The wiring was a little more tricky because it required running a power wire all the way to the battery. I towed my trailer from Florida to Tennessee and back. Etrailer is still wonderful to deal with as they always have been in the past. My hitch came in a couple of days. I wouldn't think of ordering from any one else.
# 12
Curt Class II Drawbar - 5" Rise - 11-5/8" Long - 3,500 lbs
The Curt Class II Drawbar with a 5" rise very nicely solved my problem when hooking up my two trailers to my Rave 4. The trailer jack was as low as it could go when it rested on the ball in my of setup. Now I have plenty of jack room to hook up and unhook. Thanks for your excellent product and service. Ralph E.
# 13
MaxxTow Adjustable-Height Ball Mount - 2" Hitch - 7-1/2" Drop, 6-1/4" Rise - 5,000 lb
This is exactly what I needed for my front end mounted receiver.
As advertised and quick delivery, I am an Etrailer fan!
# 14
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
Easy install, everything included, and great instructional video. Worked out great for my RAV4.
Excellent item delivered in a reasonable time. The items exceeded my minimum needs in many ways.
# 15
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
The 5 inch rise on this hitch ball mount was perfect for my 07 Toyota Rav4. The rear door opens to the side on this year Rav4 and it has plenty of clearance. I tow a 16 ft aluminium boat and this 5 inch rise ball mount works perfectly on the Rav.
Ordered this product for my 2015 Rav 4 and it has worked perfectly. I tow a trailer about 4 times a week and needed a hitch that would step the ball up to make the trailer level and allow the wheel to be lowered without manually lifting the trailer myself. Product came quickly and was advertised. Would order again if I needed one for another vehicle.
# 16
etrailer Ball Mount Kit for 2" Hitches - 3/4" Rise or 2" Drop - 7,500 lbs
Good price and works as it should.
# 17
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
Superb quality product that solved my RAV4 rear hatch to trailer winch post problem with it's extra long length!! Super fast shipping!! Can't get any better than etrailer!! Thanks!!
2007 Toyota Rav4 owner. I needed this to reach out beyond my spare tire, works perfectly and no clanging or unnecessary movement.
# 18
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.
This slightly longer than average bar was perfect for my application. The drop length was perfect also for the application. As usual, eTrailer's site and retail experience was first rate. Lots of info and specs (and videos) available makes it easier to get that piece of mind knowing that what you needed was what you ordered.
# 19
Curt Class III Drawbar - 2" Rise - 4" Drop - 13" Long - 7,500 lbs
For a 7,500 lb hitch, I was surprised it didn’t have a wedge support welded on where the flat iron is welded to the square tube.
Just what I needed, most receivers would not allow me to open the tail gate on my 2022 dodge ram without hitting the trailers crank used to mount and dismount the car hauler trailer, this receiver give me the extra few inches I needed and it works perfectly, I tried many local sources but they all came up too short, etrailer is the place to go for all trailer parts, they seem to know and sell exactly what you may need
# 20
Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
My order was missing installation parts, but the etrailer team were quick to correct the issue. Even without a lift, I was able to install the receiver and brake light cable quickly, thanks to their extensive video libray.
What our customers are saying:
"Just a note to thank you and the staff for your prompt response to my small order."