Best 2016 Jeep Compass Trailer Hitch Ball Mounts

Works great!

No issues

The product is good but a bit tideous and after installing it my bracket fell and it was a pain to get replace it support made me buy the replacement pieces and the bracket didnt come with just the bolts, and at the end they told i have i had to buy the whole unit because based on their system my truck didnt have issues with installement and the manufacturer didnt supply that bracket cause it special order so in general i dont recommend in my choice better to get it welded.

Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.

The hitch and ball mount are excellent quality. My concerns are twofold. The hitch is so heavy that I had to take it to my mechanic to have it installed. Minor cost and inconvenience, but the hitch for my previous F-150 was just as sturdy, but easy to install myself (albeit with higher ground clearance). My concern about the ball mount is that the factory told me erroneously that it could not be reversed for a drop, so I returned it. This order is for the replacement after I was finally correctly told it could be reversed and how to do that. Ball mount would have been a 3 for that reason, and overall hitch and ball mount quality a 5. So I averaged them.

I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.

I purchased the etrailer.com 2-3/4 " Rise or 4" Drop Ball Mount Kit, Curt Trailer Hitch Receiver and Twist-in 7-Pole RV-Style Trailer Connector for my 2011 Chevy Silverado. Quick Delivery! All the necessary parts arrived in perfect condition. Directions were spot on and the instructional videos were great.

WOW! What can I say? Easiest install ever! I called ahead of time and spoke with Katie about what I needed. She confirmed what I wanted would work with my van. I'm in the shipping business. The bar arrived in mint condition in a double wall box with the accessories boxed separately. After removing the hardware, reading the instructions and watching their video online, I went to work. The whole thing took less than 20 mins and I did not have to remove the exhaust. I actually used it to help hold the bar up. It took longer to remove the mud guard and rear body molding than to install. It is heavy, weighing in at about 65lbs but I did not even have to use a jack on the van. I'm very happy with my purchase and can now put bikes on the back of the van rather than in the van. I can tow our Cub Scout trailer and hall my sons football teams gear with the optional rear carrying racks. I also love the fact that the bar hides about 6" behind the bumper preventing injuries to the shins. The price was cheap and the install a breeze.

The welding splatter found its way to the hitch pin hole and it took me some time with a Dremel to clean it out so the hitch pin would slide in.

Each edge of the hitch receiver shipping carton was pierced by mounting brackets, but no damage fortunately. Consider adding another layer of cardboard padding?

I'll start off with the great customer service, called a rep for assistance and did a great job. He walked me through everything for about 5 minutes. Then I proceeded to order parts at a very reasonable price. Shipping was right on time and tracking was top notch. Now for the parts I received. Trailer hitch receiver was built like a tank, and very easy to install. I didn't even have to take off the whole bumper which I see on your website. There is only one problem with this hitch receiver. Zip ties to hold the facia bracket? It's like putting a $10 paint job on a Rolls Royce. I'm sure you have a good R&D department, but this is unacceptable. I could tell you how to make this better but I'm not part of your team. Could be solved by putting a ___ on the ______. R&D should be smart enough and paid well to figure this out. No offense but they can do better. ??ZIP TIES?? Also, it is pitched with a cap but did not receive that. I also purchased A brake controller P3 and a ball hitch. The ball hitch is pictured wrong on your website. It's pictured with an adjustable ball hitch. This is what really wanted but got something entirely different. If it works, I'll be fine with it. I should have caught that, but my eyes adjusted on the adjustable ball hitch. P3 brake controller was very easy to install, about 5 minutes. On a closing note, I will order from etrailer again. Thanks for your business. Just please listen to your customers and fix these problems. Everything and everybody are not perfect. Thanks again.

This is a great all-purpose hitch. I've used it to mount a heavy-duty bike rack and a steel T-rack to carry a canoe as well as lumber. Most recently I hauled 5 x 8 cargo trailers full of plants, then furniture for a 600-mile move. It was simple to use, problem free, very strong and sturdy. Now that I live on some acreage, I see a trailer in my future, so this will get a lot more use. I drive a 2013 Tacoma, so this is a good size hitch at a good price with sufficient capacity for my needs. I do use a key lock for the hitch as well.

Does the job, however there's a lot of play when hitch mount is inserted into the hitch and when towing with an empty trailer. Very loud. Have to buy a silencer that goes around and secures the product.

Thank you etrailer for the quality products I received early last year. We needed a trailer hitch to install on our Subaru Forester for our move from Gig Harbor, WA to Spokane. We received the hitch hardware including the tow bar and electrical harness. The entire process took 4 hours. The installation process went off without a hitch (bun intended) using detailed videos I found online. Thank you etrailer.

Good price and works as it should.

Wonderful product. I had the hitch installed in 10 minutes. The wiring was a little more tricky because it required running a power wire all the way to the battery. I towed my trailer from Florida to Tennessee and back. Etrailer is still wonderful to deal with as they always have been in the past. My hitch came in a couple of days. I wouldn't think of ordering from any one else.

I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!

Well made hitch. No ragged edged welds, all edges are smooth and painted. Even got a hitch pin with it. Fast shipping, good customer communications. ALl in all happy with purchase and company.

We sold our small motor home and purchased a small travel trailer. This hitch provided a perfect solution to how to use our bike rack while towing the trailer. It even allows room for the pickup tailgate to be lowered without removing the bikes from the rack. The hitch is very hefty with a high weight limit - plenty for the GVW of the trailer (7,000#) plus 125# of rack and bikes.

Excellent hitch easy installation.It only took me about an hr and half to install from start to finish

I purchased this Curt Ball mount 10-1/4" because I also bought ball hitch mounted mud flaps and my existing hitch was too short.This hitch was maybe a little too long, but it should work.I hope this combination will protect my horse trailer from my nasty gravel roads!

With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.

Excellent product! With the three different ball sizes, this tri-ball mount gives you a lot of flexibility. Gone are the days of having several different ball mounts to fit different tongues. High quality construction makes this an excellent investment.

definitely solid as a rock

It is heavy duty and well-built. I am not disappointed at all and I get comments everyone smile from people who are used to traveling overseas asking where I got the European style hitch from. The only downside is the lack of interchangeability in the size of the ball itself but I don’t think that’s a big deal because I set it up for what I need it for and keep a vehicle vehicle for longer periods of time.

Solid, heavy as heck. Bought this model because 1) I only have 1 lightweight trailer (Malone xtralight, also purchased from etrailer at the same time) and it’s light weight. 2) I am stuffing this into an adaptor also bought from etrailer to further stuff into a receiver also purchased from etrailer. 3) All this is on the back of my 2018 Subaru Outback. Beings that it’s a Subaru it’s not going to be used to drag a huge or heavy trailer. I’ll repeat this part in my review of the adapter, buy probably from etrailer, a receiver lock that is sleeved, to be both 1/22 and 5/8 and long. That way if you don’t want this sticking way out the back (shin killer) you can use 1 lock and go all the way through receiver/ adapter/ and this ball mount. Otherwise buy you’ll need 2 locks 1 for receiver to adapter 5/8 and a second 1/22 to go through adapter into this unit. A side benefit is it’s just different. It’s not an everyday boring looking ball mount, it’s heavy duty so why not.

Great purchase experience. eTrailer has this convenient package of ball and hitch already torqued together, AND includes a locking pin in addition to the normal cotter pin! Website is clear on details of package, contents, and dimensions of each component. Shipping was fast and packaged well. I’m not sure if I saved money compared to buying all this separately, but I’m going to believe I did. Thanks!

dodge journey 2014 etrailer service excellent the hitch don't fit perfect with the spare tire other ways is pretty good if you tele out the spare tire you going to have a hard time to put them back etrailer sevicio es excelente la pieza no se acopla perfecto con la rueda de repuesto del resto se monta perfecto . si se retira la rueda de repuesto es muy dificil de poner de vuelta en el compartimento

The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.

This slightly longer than average bar was perfect for my application. The drop length was perfect also for the application. As usual, eTrailer's site and retail experience was first rate. Lots of info and specs (and videos) available makes it easier to get that piece of mind knowing that what you needed was what you ordered.

Works well for my 2017.5 jeep compass. Thanks etrailer!

I purchased Curt's 6" drop ball mount for my 2012 Jeep Wrangler Sport which is not lifted but has 32" tall tires. The utility trailer I plan to purchase recommends a 12" tongue/ball height for level towing. The Curt 6" drop ball mount places my tongue/ball height at 13.5" which is acceptable. The bottom of my tow ball mounting nut is now 12" above the road surface. Plenty of clearance for safe towing. I'm very pleased with the quality and functionality of my Curt ball mount. I'm looking forward to purchasing a utility trailer soon. I think it will tow very nicely using my Curt 6" drop ball hitch.

Fits our VW Touareg perfectly and allows us to tow a variety of things now. As can be seen in the pictures the hitch has a +5-inch gap between the bumper and the vertical adjustment pillar and the trailer itself is out further so there's enough room to get to the rear hatch and maneuver the vehicle/trailer.

I needed a hitch that I could haul my work trailer with and still drop the tailgate without dropping the trailer. I looked on etrailer and found one that would work barely but decided to call etrailer and see if anyone had any ideas. Steve answered and looked after I told him my requirements and came up with this. This has a longer distance from ball to pin by a few inches compared to the one I found so my tailgate will still drop even if I’m at an angle to my trailer or on a hill. Also with the adjustable height it’s great. Awesome hitch. Solid for a good price. ??

I needed to tow a trailer with a 2" ball. My original ball mount has a 1 7/8" ball installed. I had previously tried to change a ball on a hitch and destroyed the nut and damaged the underside of the ball mount. The lock washer had done a great job in keeping the nut from coming off. I dreaded trying to remove my 1 7/8" ball to install a new one that I would only use once. I decided to buy a new ball mount and mount the new 2" ball. This ball mount is so inexpensive that I realized I could have both ball sizes permanently mounted for use in either ball size.

I wasn't sure what type of ball mount I needed for my new Mazda CX-9, so I had to call a representative. The first time I called, the very knowledgeable gentlemen told me exactly how to measure my SUV to figure out the drop I needed. I called back the next day and talked to a lady who helped me figure out exactly what I needed. This is my second purchase from etrailer. The first was a hitch for my old Honda Odyssey, which was also a great experience. The employees are so helpful, the video tutorials on the web site are fantastic and the prices are great. etrailer.com is the first place I go to look for trailer and towing supplies!

The hitch was delivered as ordered. The 2" ball was torqued on and it is a perfect fit to the receiver. Solid and high quality. etrailer.com has continued to be a great online retailer for me.

Paul/ you were a great help. Told me everything I needed to know. It works fine each time I use it. Thank you, Scott