Most Popular LED Light for 2016 Jayco Jay Flight Travel Trailer

Have not installed yet but looks as described.

First unit arrived broken and was replaced by etrailer no problems. Many thanks to everyone at etrailer.

My replacement lights came quickly and were quite easy to install.

Bright….! The exact replacement.

they fit, water proof tape needs to be included for the price.

Lights were an easy, direct replacement for the incandescent factory lights that came stock on the trailer. Splicing was necessary but the wiring colors were accurate as this is the same manufacturer as oem. I am hoping the LED style last longer than the original. If not I will switch to another brand.

These are great. They fit into a 2x4 piece of steel C channel very nicely. This makes for a very strong and easy to mount combo that actually holds up when pulling the trailer off road. The stock tail light housing was very thin and would rip off going over uneven terrain, not to mention the oval lights would vibrate out. These lights bolt on and won’t fall out.

These are exactly what I was looking for

Installed on a 93 Skeeter boat trailer. Very tight fit. Had to turn the light sideways and push through Grommet to install . Right now I have it installed but until I take the boat out this weekend, I will not know if I have the wires plugged in correctly. 50/50 chance of getting it correct. Shipping was very fast.

Replaced all the clearance/marker lights on my 2007 RV. Nice upgrade to the LED and very easy installation.

The clearance lights work perfectly. The sales lady went above and be beyond to make sure they were correct. She even went back in the data and found a previous order I made. Very professional!

I should have looked at the photos more closely, as the wiring comes directly out of the rear of the light. The wiring on the OEM light I replaced was a bit more flexible for mounting the light on the fronts of the two fenders on my tow dolly. Also, the mounting holes for the hardware were a larger diameter than I expected, so I had to use washers to keep the smallish bolts from pulling through. On the other hand, the LED lights are brighter than the incandescent bulbs in the OEM lights and they will NOT come loose from road vibration as did the cheesy bulbs and bulb mounts in the OEM lights. Overall, a definite step up for use. The only complaint was the extra time deciding how to accomplish the wiring and mounting.

Easy install. Be sure to check base of wires on the light. The severe bend in them can crack the insulation and may cause issues. One of mine had it and had to doctor it up, otherwise 5 stars.

OEM product for a great price

The products seem well built. I replaced originals on 5th wheel RV to match new clearance lights. Larger and brighter than the original lights. I would rate it a 5 star if the product included screws and gaskets to prevent water intrusion.

Nice lights, a bit over priced but work well. I have them mounted on my trailer so I can see the end of the trailer in both mirrors when traveling straight.

Thank you perfect fit.

Was the same size as original equipment.

We have upgraded all our trailers to LED. This is the first light we have replaced in 7 years. We use etrailer for all our trailer lighting.

The cover almost fit perfectly. Well built. Held up well to a harsh winter. A surprising find was that it keeps our fifth wheel dust free on the inside as well as the outside. well worth the expense.

I ordered this product as an exact replacement for the one I had to replace. Placing he order and checkout was extremely easy. Via there website I was able to track the entire process from ordering, handling and the shipping process. Etrailer is company I have in the past and will continue using.

Our tail light quit working during our vacation - we checked with a local RV shop and they told us the part was on back order and they wouldn’t have it for 4 weeks. We found it on trailer and ordered it and had the light in 4 days delivered to the campground we were staying at- Thank you etrailer!!!

Exactly what I was looking for.

Perfect fit for replacement. Quick shipping.

It was an exact replacement. Works great. Thanks

Terrific upgrade in my opinion. The installation was pretty easy for me. The light is slightly smaller than the original and I have the corrugated sheet metal siding I did not experience any led hyper flash with this light. I was slightly concerned about this after seeing videos of people changing to led light bulbs on the tow vehicle. This light was plug and play. 4 stars because the manufacturer did not provide a wiring diagram :( I don’t feel you should guess what wire goes where. The least they could do is tell you what they (the manufacturer) wired for ground. In my case, the white was ground, same as my trailer wiring. However I needed to connect green to black to get my turn signal to work. Your situation may be different. Would I buy it again? At this time, yes. I’m hoping this light outlasts my usage of this travel trailer- which should be for many years.

Very bright light, same connectors as my 2001 Shoreland'r boat trailer, just had to plug them in. Cannot say enough about the staff at etrailer, very helpful.

SPLENDID! Popped the old incandescent Side Marker Lights out on my 2008 Triton 21X2 trailer and installed these Thinline LED Clearance and Side Marker Lights (both the AMBER and RED ones). Just Plug-N-Play and my boat trailer looks AWESOME! Shipping was a snap!

Replace the LED strip under my Awning on my Jayco trailer with these and used shrink tubes to make the connections water tight also . Work really great!!

Great service! My order was shipped the same day as my order. The lights are high quality for a good price. Will definitely be using etrailer for my rv needs.

Just got my lights they look great but l will have to wait till it warms up from -15 to install them

Tail light delivered on time and easy to install . LED’s much brighter and visible than the original incandescent bulb. Nice lights!

Quite easy to install and fit my Coachman Freelander perfectly. The prior ones were not sealed, filled with water, and blew the fuse fuse. Beware of the cheaper version on Amazon as they have the same poor seal problem as the original lights which died after <5 years.

Command Triple LED Tail Light Review They work great once they are installed. I have 2002 Gulf Stream Ultra on a Ford E450 Frame. The problem is the actual installation. Command does not include install instructions. What may needed if converting from incandescent bulb to a LED system is a 12 Volt 50 Watt 6 Ohm resistor. Installing a resistor parallel between the Brake/signal and Common wire will be necessary to overcome the hyper-flasher bulb out detection system. This high power resistor needs to be mounted on a metal surface to help disapate the heat created. In my case, I mounted the resistor to 3/4 metal pipe banding. The resistor was suspended so that is would have great air flow. Furthermore, size of the light should be slightly larger than 14 w x 6 7/8 . In my case the tail light was not big enough to cover the old light screw holes. I made this work by centering the light and using lap sealant as a finishing water proof bead. After a long road trip and many signal turns and brake presses the tail lights do look and work great.

I had to upgrade my previous LED lights that i purchased years ago from here as they were all blown out minus 1 bulb on each side. These lights fit right into the preious bracket with the previous gasket and they light up well.

I used these on my plow truck's new flatbed. I liked that it included the mounting grommets and wiring pig tails. They are working terrific, and look stylish.

This trailer light was an exact match for my original equipment light and easy installation.

I needed a tail/stop light for the rear of my Fairmont railway motorcar and thought from your on-line description that this product would be satisfactory. I was right, it is a good size and bright enough to be very visible in bright sunlight. As you can see from the pictures, to make it match aesthetically I attached the lamp to an aluminum plate cut to fit in an old auxiliary lamp housing. The railway car runs in both directions hence has head and tail lights on both ends. I am very satisfied with this light.