Best 2016 Ford Edge Trailer Hitch Ball Mounts

Exactly what I needed. All my previous SUVs used 2x2 hitch mounts which now are useless.So I decided to gift them to my son. The hitch mount is well made. etrailer is fast and very easy to find exactly what you need at a fair price. Customer service is friendly and helpful.

Perfect fit for my hitch and trailer. Pulled really well.

Follow directions. It is an easy install. Just takes time.

Nice solid (not hollow) and WELDED hitch. Have logged about 5,000 miles this year with no problems. I had many problems with bolted on balls, welded hitches are the way to go.

The product is good but a bit tideous and after installing it my bracket fell and it was a pain to get replace it support made me buy the replacement pieces and the bracket didnt come with just the bolts, and at the end they told i have i had to buy the whole unit because based on their system my truck didnt have issues with installement and the manufacturer didnt supply that bracket cause it special order so in general i dont recommend in my choice better to get it welded.

Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.

A year has passed with my Convert-A-Ball Dual-Cushioned, Adjustable Ball Mount and I have nothing but praise for this mount. Once you find the correct height to have a perfectly level trailer there's no need to adjust. The beauty lies in the cushioning! Towing a Yamaha AR190 (3200lb boat and trailer combo) is silent. Even over the bumpiest pavement the tow is smooth. There is no harsh slamming when braking or taking off from the boat ramp. I don't know why everyone isn't running one of these, I wouldn't run any other hitch mount PERIOD! If you're on the fence, get off and buy one, you will NOT regret it!

We bought this to tow our 3,000 lbs. boat with our Subaru Ascent with a 5,000 lbs. towing capacity. With the OEM ball mount, we could really feel every jolt and jiggle from hard stops, going over bumps in the road, and trailering down dirt roads. However, the dual cushion ball has really improved our trailing experience. Once we get up to speed, we hardly notice we are towing our boat. It's also great because some of the lakes we visit are down dirt roads, and the cushion makes this a much more pleasant experience. I would highly recommend this to anyone towing a boat or larger trailer with a SUV as it maintains that comfortable ride and the jostling of the trailer is much less noticeable.

This ball mount has served it purpose well. I purchased a new travel trailer that is heavy enough to require a weight distribution hitch when using the factory installed Class III hitch on our Dodge RAM 2500. I decided to upgrade to a Class V hitch combined with this ball mount to take delivery of the TT in order to defer decisions about a WD hitch until the actual load conditions were known. The hour trip home with this setup worked very well. Once the trailer was outfitted I was able to determine the actual tongue weight of the loaded trailer and I decided to purchase an appropriately sized Reese Straight Line WD hitch. However, this ball mount comes in handy for moving the trailer short distances without hassling with the WD system. The purchase experience through etrailer.com was first rate.

I was surprised at the heft and quality of the ball mount. Shipping was fast, communication good, easy and informative website to use. Thanks etrailer, you have earned a new customer!

Heavy duty , very good quality.

I installed one of your Draw Tite trailer hitchs on my 2014 Ford Edge. However my carrier would not fold up without hitting my car. I just ordered a Draw Tite hitch for my wife's MKX and stumbled on this accessory which solved the problem. Hell to get old!

This draw bar in perfect for my John Deere X738 tractor. What I like about it is the ¾” rise it keep the draw bar height at about the same as the factory frame so the attachments height remain level. Thanks for the great product.

Not much you can say about a bar with a piece of flat metal welded to it; well made looks good. What is really important is that e-trailer is fast, friendly and knowledgeable. I've ordered from them anytime I needed a trailer/RV part.

tl;dr good experience with warts. The etrailer-branded ball mount kit I ordered was back-ordered for a month, which was fine. Eventually Ashley E told me it would be a _second_ month. Not fine. She helped me configure a new order of third party parts. Shipped in one day. Great! Not great: Parts were just thrown in a box with no protection. UPS did their usual thing. Paint was chipped in a couple of places; would surely rust. I'll shoot these spots with some spray paint before installation. Hope that's a fix. I can't afford to diddle with a return.

Good fit, well made, worked well on first use, ball attached easily, was the reciever I was looking for.

EVERTHING WAS EXCELLENT FROM PLACING THE ORDER TO RECEIVING THE PACKAGE AS WELL AS THE FOLLOW UP. WOULD STRONGLY RECOMMEND ETRAILER....

Heavy duty hitch. Well built and welds are fine.

Very happy with the fit and finish of the product. What I like most is the extra extension it allows for with out derating. My problem centered on tailgate clearence when in the open position. Tailgate would contact the edge of the tounge jack. This solved that problem plus now I don't need to carry seperate ball mounts for my boat or enclosed trailer

Fits our VW Touareg perfectly and allows us to tow a variety of things now. As can be seen in the pictures the hitch has a +5-inch gap between the bumper and the vertical adjustment pillar and the trailer itself is out further so there's enough room to get to the rear hatch and maneuver the vehicle/trailer.

The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.

This slightly longer than average bar was perfect for my application. The drop length was perfect also for the application. As usual, eTrailer's site and retail experience was first rate. Lots of info and specs (and videos) available makes it easier to get that piece of mind knowing that what you needed was what you ordered.

Purchased this hitch as a companion for our Reese anti sway control. The small ball for the Reese sway control fits in the bracket and the 2” drop on the hitch is exactly what we needed to have our Jayco camper level when towing.

I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.

This ball mount fit the SUV just right. I needed a 5 inch rise and the mount angled away from the bumper. However, the load capacity was way more than I needed, but the fit made up for that. It's a little loose in the receiver so I will be adding a stabalizer to lock it in place.

Its been a year and I aint broke it yet. I use this hitch to tow my 7Klb trailer. The trailer is tongue heavy and I needed something rugged to tow it with. Haven't had any troubles with this hitch.

GLORIOUS!!! Bought this item with zero experience, but much research. It is the best vehicle-related purchase I have ever made! Item performs exactly as advertised, even in spite of much abuse I have given it. Just because I could, I load tested it right at the edge of the max distributed towing weight, multiple times. No problems ever! Easy to install properly and safely!!! Well made construction! In my opinion, the best on the market at any price, but fortunately not the highest price by a pleasant margin!!!

I bought this hitch to fit my 2017 Ford edge. I'm impressed with the quality and sturdy construction. I will be using it to haul a U-Haul trailer. I would certainly recommend this insert to anyone looking for a fairly priced solution.

Just what I needed. Shipped and received when etrailer said it would. Not my first order and they are always one of my first visits when I need something for my trailer.

Again, Will the eTrailer rep really helped me get exactly what was needed for my application which was a little out of the ordinary. I could tell he had the knowledge and experience to direct me to the correct solution.

The team at etrailer relayed helped find the right solution. Using this ball mount fixed the height issue I had with my SUV not lining up with the trailer. Very grateful for their help.

I've used the hitch over the last year on several trailers and loads. The adjustability made towing a much better feel and ride over a fixed hitch that at times not the greatest. I see no wear, very easy to adjust even once coupled to the trailer and finding the trailer needs to be leveled better.

I pay to receive the product in good condition, my hitch ended up being damaged, I don't know what type of packaging this was, they are supposedly a waoooo site, I ask for my return label and my refund, I

I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.

This drawbar did exactly what I was hoping for. It leveled out my trailer and took the weight off the tongue. Perfect!

Purchased to extend the trailer away from the back of the vehicle, and increase the drop. Initially could not fit in to my receiver, eventually figured out that the end of the 2" square was mushroomed, had to remove excess metal with a rotary tool. now it fits as far as the first 5/8" pin hole. No issues with use - seems sturdy, metal finish seems durable. Didn't drop the trailer tongue as much as I had hoped, but that's on me - I was probably running a 3" drop before, but I thought it was 2".

Dual length to get past a spare tyre mounted to the rear door. The 1’ hole allows for a heavier grade of ball to be mounted. The product is well made and packaged. I found etrailer some years ago after doing a global search for a product that I needed. I have found the company to be top notch in terms of service, price, availability, communication and customer service - it’s now my go-to company for trailer (and other) related products.