See what our Experts say about this CURT Trailer Hitch Ball Mount

• Trailer Hitch Recommendations for a 2005 Toyota Highlander
  On the 2005 Toyota Highlander, the available hitches all clear the bumper and stick out past it about 4 inches, The Draw-Tite (75153) and Curt Hitch (13530) in this case are actually very similar, so it will look the same. Both hitches have the same basic specifications. They are all Class III hitches with 2 inch receiver openings. The Curt # 13530 is rated for weight distribution, with a 4000 lb GTW and a 400 lb TW rating, while the Draw-Tite model is not rated for weight distribution. I...
  view full answer...
• Recommendation For a Trailer Hitch That Will Fit 2006 Mercedes-Benz ML350
  The item you selected, Curt Class III Trailer Hitch, part # 13342, is the hitch I would recommend for your 2006 Mercedes Benz ML350. This is a Class III Hitch, with a 2 inch receiver that is compatible with most accessories such as cargo carriers or bike racks. This is the highest rated hitch available for your 2006 Mercedes-Benz ML350 for towing. In addition to part # 13342, you may need the following to complete your towing setup: Ball Mount part # C45010, Pin and Clip part #...
  view full answer...
• Trailer Hitch, Ball Mount, Hitch Ball, and Hitch Lock Recommendations for a 2007 Mercedes ML350
  Yes, the Curt Class III Trailer Hitch Receiver, # 13342, is a confirmed for your 2007 Mercedes ML350 as long as it does not have the Air Ride Suspension. I have included a link to the instructions below. Hitches do not come with a ball mount. So you might also be interested in Ball Mount # C45010, and a ball. For hitch balls you can use, # 19260 (1-7/8 inch diameter), # 63845 (2 inch diameter), or # 63853 (2-5/16 inch diameter) depending on your towing needs. I also recommend a Trailer...
  view full answer...
• Sway Control Recommendation for Vehicle with 1-1/4 inch Hitch
  We have friction sway control units that will work great to prevent the type of sway you are describing. For that the Curt part # 17200 would be a really great option. You'd use the bracket part # RP26005 installed on your hitch ball and then you'd be set. Friction sway control was designed to fight the exact type of sway you mentioned that is caused by wind from passing semis or just high winds in general. Proper trailer loading makes the biggest difference in preventing sway as well....
  view full answer...
• Can Trailer Hitch from 2010 Volvo XC60 Be Used on 2012 XC90?
  We do have a hitch fit for the 2012 Volvo XC90, but unfortunately the 2010 Volvo XC60 and and a 2012 XC90 use different hitches. For the 2012 XC90, I'd recommend the Curt Class IIl hitch, part # 13559. If you'll be towing with the hitch, you'll also need a trailer wiring harness, part # 118411, a # C45010 ball mount and for a trailer ball, use # 40038 for a 1-7/8 or # 63845 for a 2 inch ball.
  view full answer...
• Kayak Carrier Recommended for Old Town Heron Kayaks on Yakima Y08107 Rack and Roll Trailer
  For a fairly economical way to transport your three kayaks on the # Y08107 Rack and Roll trailer, I'd recommend going with the Malone FoldAway # MAL38FR for two kayaks and the # MAL98FR for the third. I looked up your kayaks, and found that Old Town lists the weight of the solo as being about 40 lbs with a length of 9-1/2 feet and the tandems as being 60 lbs each with a length of 13-1/2 feet. The kayaks sizes and weights would be compatible with both the Rack and Roll trailer and the carriers...
  view full answer...
  
• Recommended Trailer Hitch For 2020 Mercedes-Benz Sprinter 2500 Long Wheelbase Standard Bumper
  As long as your 2020 Sprinter 2500 with the 170 inch wheelbase and standard bumper isn't a passenger van and the frame members do NOT measure 30-3/8 inches apart measured outside of frame to outside of frame, the Curt Class III hitch, part # C13388 will fit perfectly. If you have the passenger version, you'll want to use the Draw-Tite # 75549 instead. If you'll be towing with the hitch, you'll also need a trailer wiring harness like part # TK82VR for a 4 pin connector or # TK22115 for...
  view full answer...
• Differences Between etrailer Brand and Curt Trailer Hitches for 2020 Chevy Colorado
  The differences between the Curt # C13203 and the etrailer branded # e98909 are primarily cosmetic. Both hitches would be mainly concealed behind the bumper, with only the receiver tube and the safety chain hooks being visible. The Curt uses a round tube crossbar with a glossy finish, the etrailer brand hitch uses a square crossbar with a matte finish. The cosmetic appearance really won't matter much as most of the hitch is concealed anyway. The Curt hitch has s higher capacity than the...
  view full answer...
• Trailer Hitch for 2001 Mitsubishi Montero Limited
  We do indeed offer Class III receiver hitches for the 2001 Mitsubishi Montero and Montero Sport (two distinctly different vehicles). For the 2001 Montero, use the Curt Class # C13800 III hitch. If you'll be towing with the hitch you'll also need a trailer wiring harness like # C55380 a ball mount like # C45010 and # 19260 for a 1-7/8 or # 63845 for a 2 inch trailer ball. For the 2001 Montero Sport, you'd use the Curt Class III, part # 13223. For trailer wiring, use # 119178KIT and the...
  view full answer...
• Differences Between Curt Class III Trailer Hitches for 2015 Subaru Forester
  The primary difference between the two is that once installed, the # C13144 will be completely visible from the rear of the vehicle. The # CU64FR is designed a bit differently, the hitch crossbar will be concealed behind the bumper with the only visible portion of the hitch being the receiver tube and the safety chain hoops. The # CU64FR is preferred by most because the entire hitch isn't visible. Because we pay more for the hitch and it's more in demand, the # C13144 is priced higher....
  view full answer...
  
• Why Does Ball Mount BH20 Have a Solid Shank While Ball Mount 2923 is Hollow
  When the shank of a ball mount or hitch-mount accessory - say a bike rack for example - is solid rather than hollow this typically means it will be stronger. It also means it will be heavier. The Brophy Ball Mount # BH20 has a solid steel shank which is part of why it has a very substantial 10,000-lb weight rating. The roughly similar Curt ball mount # C45010 offers a 7500-lb weight rating; Even though it is not a solid shank, it does have a very thick platform for our ball to attach. Hollow...
  view full answer...
• Fit of Draw-Tite 76333 on 2021 Subaru Outback XT With Dual Exhaust
  It sure will, and here's why.... The Draw-Tite 76597 which we sell as part # DT94YR doesn't actually install under the vehicle where the exhaust could possibly interfere with the fit of the hitch. The hitch actually installs between the factory bumper/crash beam and the body of the vehicle which is above and rearward of the exhaust. I've linked to an install video showing the hitch being installed on a 2021 Subaru Outback XT like yours. In the video, you can clearly see how the hitch...
  view full answer...
• Installed Height of etrailer Brand Hitch Receiver e98847 on 2019 Subaru Outback Wagon
  When we installed the etrailer brand # e98847 receiver hitch on a 2019 Subaru Outback Wagon, we found the receiver height to be right at 16 inches, as shown in the linked install video. The average trailer coupler height is around 16 inches, so a ball mount like # C45010 would be about right. For a 1-7/8 inch trailer ball, I'd recommend # 19260 or # 63845 for a 2 inch ball. For a trailer wiring harness, use # 118467. I'll link you to installation instructions/videos for the hitch and the...
  view full answer...
• Trailer Hitch and Wiring for 2022 Blazer
  As long as your 2022 Blazer isn't the Premier model, we do indeed offer a hitch and wiring harness that would work for you. I'd recommend the US made Curt # C13418 Class III hitch. For a trailer wiring harness, use the # 118720 for a 4-pole trailer connector. For a ball mount, use # C45010 along with # 40038 for a 1-7/8 inch or # 63845 for a 2 inch trailer ball.
  view full answer...
• Can a 2 Inch Trailer Hitch Ball Be Replaced with a 1-7/8 Inch Hitch Ball on a 2 Inch Hitch Receiver
  To replace the hitch ball you would simply loosen and remove the hitch ball nut and pull the ball out of the ball mount hole. You may need a large wrench to loosen the nut. The Tow Ready 1-7/8 Inch Hitch Ball, part # 19260, would be a great fit for your application, as it features a 1 inch diameter shank that should be compatible with your ball mount. Please note, however, that some ball mounts for 2 inch x 2 inch hitches require a hitch ball with a 1-1/4 inch shank. If your current...
  view full answer...
  
• Trailer Hitch and Wiring Harness Recommendation for 2018 Subaru Outback
  Although I'd love to sell you the EcoHitch # 306-X7601, the Curt Class III part # C13410 will be just as concealed as the EcoHitch at a lower cost. Curt makes a high quality product that's on par with that of EcoHitch. In this instance you'll sacrifice absolutely nothing by going with the less expensive option. The upside of the EcoHitch is that it is made in the USA and has a mission to recycled materials. Since you'll be towing at some point in the future, there's really no reason not...
  view full answer...
  
• What is Needed to Flat Tow a 2007 Pontiac Vibe Behind an RV
  To tow your 2007 Pontiac Vibe behind your RV, you will first need to install a base plate kit. For your vehicle, you will need the Roadmaster XL Base Plate Kit, # 3130-1. Base plate kits are vehicle specific and this one is made to fit your Vibe. I have included a video that shows a base plate kit being installed to give you a general idea of what it entails. Next you will attach a tow bar. The RoadMaster Tracker, # RM-020, is designed to be compatible with the XL series of base plates....
  view full answer...
• Trailer Hitch for a 1996 Ford Explorer Eddie Bauer
  For your specific vehicle I would recommend the Draw-Tite Class III Trailer Hitch Receiver # 75083. I have included a video that shows this product being installed on a 1996 Ford Explorer. For wiring I also suggest the T-One Vehicle Wiring Harness with 4 Pole Trailer Connector # 118345 if you do not have a tow package. If you do have a tow package then use Tow Package Wiring Harness with 4 Pole Trailer Connector # 118241. I also have a video of this wiring being installed on a 1996 Ford...
  view full answer...
• What Does GTW and TW Mean and What is Weight Distribution, 2008 BMW X5
  I can certainly help you out. The TW is the tongue weight. This is the weight of the trailer at the coupler that attaches to the ball mount on the trailer hitch. It should be 10 to 15 percent of the GTW or gross trailer weight. The gross trailer weight is the total weight of the trailer. Weight distribution is a system that installs on the trailer frame and the trailer couples to a special shank on the trailer hitch. The spring bars that come with a weight distribution system take some...
  view full answer...
• How Visible is Draw-Tite 76209 Class III Hitch Compared to Curt C13382 on 2021 Subaru Crosstrek
  It is not. When installed, the Curt # C13382 would be mostly concealed behind the bumper fascia, with only the receiver opening and safety chain loops being visible. The Draw-Tite # 76209 will be fully exposed, with the hitch crossbar being fully visible under the rear bumper. I've provided a side-by-side photo showing the installed appearance of the two. If you'll be towing with the hitch, you'll also need a trailer wiring harness, part # 118467, a ball mount like # C45010 with pin and...
  view full answer...
  
• Why are Some Ball Mounts Longer Than Others?
  The reason some ball mounts have different lengths is simply to allow for more clearance between the tow vehicle and trailer. Some people like a longer ball mount if, for example, they want to be able to open the tailgate of their truck when the trailer is attached. Something like the Curt # C45270, which is 13" long may allow that while Curt # C45010, which is 8-1/4" long, may not. I've added a link to each of our ball mounts for you to take a look at.
  view full answer...
• Recommended Hitch Fit for 2009 Ford Escape Hybrid
  I'd recommend a Curt Class III receiver for your Escape. Curt makes a great product with a durable powder coat finish. The hitch you need will depend on if your Escape is already equipped with the factory 1-1/4 inch hitch. If it is, you'll want to use # C13651. If it isn't, use # 13650. As confirmed by Curt, these hitches are compatible with the hybrid model, and the only slight issue you might run into is if your Escape is equipped with the exhaust dampener as shown in the provided...
  view full answer...
  
• Is Cutiing Required for Installation of the Mercedes-Benz R350 Trailer Hitch # C13103
  You will not need to cut the OEM bumper for installation of the Curt Trailer Hitch, item # C13103, for the 2008 R350 by Mercedes-Benz. There is some cutting required, but the cut areas are under the vehicle and will not be visible when the hitch is installed. If you have a vehicle with cross bracing member, and in 3 places, if your vehicle does not have the cross-bracing members. The installation instructions, see link below, show exactly where to cut the plastic trunk pan and explain...
  view full answer...
• Recommendation for Class III Trailer Hitch Receiver for 2011 Honda CR-V
  A Class II hitch would use a 1-1/4 inch receiver, for a 2 inch receiver tube you'd want a Class III hitch. We offer two US Made Class III hitches that I'd recommend, the # 13555 from Curt or the # 306-X7291 from EcoHitch. Both hitches share the same 3500 lb gross trailer weight capacity. The Curt has a tongue weight capacity of 350 lbs while the EcoHitch has a capacity of 525 lbs. The primary difference between the two is that the EcoHitch model installs so the majority of the hitch is...
  view full answer...
  

Do you have a question about this Trailer Hitch Ball Mount?