Replacement Parts for Sliding Reese 16K 5th Wheel Hitch

Question

Question:

Can I get a replacement rounded-slide-bar, single-jaw mechanism for my RP50031 5th wheel hitch?

asked by: Bob

0

Expert Reply:

For your Reese Sliding Fifth Wheel Hitch # RP30051 we offer both a replacement head unit only, part # RP58146, or the head and crossmember assembly # RP30047A. You can choose the one that includes the mix of components you need.

For the sliding legs you can use the Reese Round Tube Slider for 5th Wheel Trailer Hitches # RP50024.

expert reply by: Adam R

0

Answer 1

Yes, #RP30047A is the correct head and crossmember replacement for the Reese Fifth Wheel Hitch #RP30047.

view full answer...

Answer 2

There are many different wiring harnesses on Police Interceptors, and the photo you've attached is not a common fit for trailer wiring. I don't believe that harness is for your trailer wiring even though it looks similar. I've attached…

view full answer...

Answer 3

The closest thing we have to your jacks are the Ultra-Fab Ultra Scissor Jacks - 24" Lift - 6,500 lbs - Qty 2 #UF48-979002. These are BAL jacks that have a restricted height of 4-3/4 inches and an extended height of 28-3/4 inches. I've…

view full answer...

Answer 4

An LED light isn't going to pull much so it's odd that you'd melt the wires consistently unless those connection points are somehow touching bare metal in the wall and shorting out. I would start by first ensuring that these connection…

view full answer...

Answer 5

Yes, the product you are looking for is the #RP30047A which is just the head and crossmember of the 16K 5th wheel #RP30047. I have linked the above mentioned products to this page for your convenience.

view full answer...

Answer 6

On the slider portion of Reese 5th wheel trailer hitch #RP30051, you will need to coat top and side surfaces of slide tube and roller holes (6 places) in each slider assembly with all purpose grease or teflonlube, use as needed. Repeat this…

view full answer...

Answer 7

I spoke with my contact at Reese and he informed me that there is nothing you can adjust on the slider that will allow you to remove that play. He did say to make sure that the pull pins that attach the slider to the rails are in correctly. You will…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 12

Yes, the puck system used on the 2016-2019 Chevy/GMC trucks is different than the pucks used on the 2020 and newer trucks. So you would need a 5th wheel like the B&W Companion #BWRVK3710 for your 2020 GMC Sierra 3500 with an 8' Bed. If you…

view full answer...

Replacement Parts for Sliding Reese 16K 5th Wheel Hitch

Continue Researching