Troubleshooting 7-Way Connector of 2006 Toyota Sequoia With No 12-Volt Feed at 7-Way
Products Featured in This Question
Question:
I want to charge batteries on my utility trailer that is used for a job trailer. I have checked the wiring of the plug and there is not a pole that has Aux. power to it. In fact the 12 v. hot pole is not powered up either. Do these vehicles have Aux. power at the rear of the vehicle standard? If they do, where would it be located, and how would I go about finding it?
asked by: Paul
Expert Reply:
If your 7-way on your Sequoia was installed at the factory, the 12-volt circuit should be active. Check the fuse box under the hood for a blown or missing fuse. If there's no blown fuse, you trace the 12-volt circuit from the rear of the vehicle looking for a loose connection, but abandoning the original and installing your own circuit as described below might be the simplest course of action.
If the 7-way was installed aftermarket, check the terminal for the 12-volt pin at the rear of the 7-way. If it doesn't have a wire connected to it, you'll need to run one to the positive battery terminal. Use a length of 10 gauge wire, part # 10-1-1, and run it under the vehicle to the engine compartment. Be sure to avoid anything moving like suspension or steering components and anything hot like the exhaust system. Install a 40 amp circuit breaker near the battery, the firewall or inner fender usually works well. Attach a ring terminal like part # 44-5310A on the end of the wire, and connect it to the silver post of the breaker. Cut another length of wire long enough to reach the battery from the breaker. On one end, attach another # 44-5310A ring terminal and attach it to the copper post of the breaker, on the other end, attach a # 44-5356A ring terminal and connect it to the positive battery terminal.
Keep in mind, the 12-volt accessory circuit from the 7-way doesn't have enough grunt to recharge a dead battery. It can maintain a battery, but not charge one that's become depleted. To charge the battery, you'll need a charger like part # CTEK56353 and shore power.

Product Page this Question was Asked From
Adapter 4-Pole to 7-Pole and 4-Pole
- Trailer Wiring
- Wiring Adapters
- Multi-Function Adapter
- 4 Flat
- Plug and Lead
- 4 Flat
- 7 Round - Blade
- Hopkins
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Classic Lite License Plate Frame - Black
- Shop: Trailer License Plate Light with Housing and Mounting Bracket - Clear Lens - Black Base
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V XD - 2"
- Shop: Replacement Electric Brake Assembly Dust Shield
- Search Results: 80~01~2160
- Search Results: c15323
- Search Results: 9~27~1
- Search Results: 23~438
- Search Results: ra~28
- Search Results: bp15~150
- Search Results: 8~430
- Shop: etrailer Ball Mount w/ Pre-Torqued 2" Ball - 2" Hitch - 4" Drop - 7,500 lbs
- Shop: MaxxAir II RV and Trailer Roof Vent Cover w/ EZClip - Smoke
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Q&A: How Can I Get Power to my 7-Way Connector on my 2006 Nissan Pathfinder without a Tow Package.
- Video: All About the Hopkins Plug-In Simple Vehicle Wiring Harness for Factory Tow Package
- Q&A: Does the Hopkins Plug-In Simple Vehicle Wiring Harness # HM11143325 Include Mounting Bracket
- Video: How to Install: Curt Trailer Hitch Receiver on your 2001 Toyota Sequoia
- Article: Trailer Hitch Installation Tips
- Shop: Tire Chains
- Q&A: Help Determining if 2006 Toyota Tundra has Tow Package
- Video: Best 2006 Toyota Tacoma Trailer Hitch Options
- Video: Review of Tekonsha Wiring - Trailer Connectors - 119147KIT
- Video: Finding the Right Trailer Wiring Harness
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: How to Choose a Trailer Brake Controller
- Article: How to Measure for Trailer Hitch Drop
- Video: Installing the Towsmart Trailer Hitch Receiver on a 2024 Toyota RAV4