Fasteners for Attaching Marine Plywood Decking to Snowmobile Trailer
Question:
Greetings, I have a two place aluminum snowmobile trailer that I am replacing the decking on. I am using 5/8inch thick marine grade plywood, which is the same thickness as the OEM plywood. The OEM screws are T30 Torx 1 3/4inch long. I see that these screws are 1 1/2inch long. Will this be an issue? I have attached a photo of the OEM screws. Any advice would be greatly appreciated
asked by: Jeremy B
Expert Reply:
Thank you for the photo of one of the original decking fasteners from your aluminum snowmobile trailer. It appears your fastener has a taper at the point; but then again this might be erosion from exposure to winter road salts.
We do offer several lengths of Torx fasteners, including some specifically for ACQ-Treated wood, ranging from 1-inch (part # WLS100), 1-1/2-inch (# TF01150 that you referenced) to 2-1/4- and 2-1/2-inch lengths.
The key for your proper replacement size is the depth of the underlying trailer frame. You don't want to have less bite into the trailer frame than before, but if a 1-1/2-inch screw will reach far enough into the trailer structure then a slightly shorter fastener may be okay. Without knowing the nature of the frame's mounting point its hard to say. If you can fit a longer screw like the 2-1/4-inch # TF01225 without creating any hazard for clearance, then go for the longer fastener that provides the maximum thread contact.
If you need a Torx bit, we offer # TX430-1.
Products Referenced in This Question
2-1/4" Long Torx; Floor Screws, 40/Pkg
- Accessories and Parts
- Tie Down Anchors
- Hardware
- Torx Screw
- 2-1/4 Inch Long
- Redline
more information >
1" Long Black Torx Wall Liner Screw
- Accessories and Parts
- Tie Down Anchors
- Hardware
- Torx Screw
- 1 Inch Long
- Redline
more information >
Product Page this Question was Asked From
1-1/2" Long Torx Floor Screws, 40/Pkg
- Accessories and Parts
- Tie Down Anchors
- Hardware
- Torx Screw
- 1-1/2 Inch Long
- Redline
more information >
Continue Researching
- Shop: Brophy Rope D-Ring Tie-Down Anchor - Bolt-On - 2-1/4" Wide - Surface Mount - 1,600 lbs
- Search Results: spare tire mount
- Shop: Demco Trailer Stake Pocket Spare Tire Mount with 4" Offset - Silver
- Shop: Rambler ST205/75R15 Trailer Tire with Black Vesper Mod Wheel - 5 on 4-1/2
- Shop: "Junior" Locking Stainless Steel Flush Door Latch
- Shop: Locking Paddle Handle w/ Internal Release - 5-1/2" Long x 4-1/4" Tall - Zinc Plated Steel
- Video: Brophy Rope D-Ring Tie-Down Anchor Review
- Video: The Low-Down on the CargoSmart Anti-Rattle D-Ring Tie-Down Anchor
- Video: Breaking Down the CargoSmart Anti-Rattle D-Ring Tie-Down Anchor
- Q&A: Recommended Screws For Plywood Deck on Snowmobile
- Search Results: isolator
- Search Results: e96rr
- Q&A: Should the Breakaway Cable be Shorter or Longer Than the Safety Chains
- Shop: 1-1/2" Long Torx Floor Screws, 40/Pkg
- Shop: Spare Tire Cover
- Shop: Brophy D-Ring Tie Down Anchor - Bolt-On - 2-3/8" Wide - Surface Mount - 4,000 lbs
- Search Results: tire cover
- Search Results: shackle
- Search Results: hinges
- Search Results: window
- Video: All About the 1-1/2" Long Torx Floor Screws, 40/Pkg
- Video: Ultimate Overview of the 2-1/4" Long Torx; Floor Screws, 40/Pkg
- Video: Redline Tie Down Anchors TFX225ACQ Review
- Video: An In-Depth Look at the 1" Long Black Torx Wall Liner Screw
- Shop: RV Interior Lighting
- Shop: RV Exterior Lighting
- Q&A: Drill Bit for 2-1/2" Long Torx Trailer Floor and Wall Liner Screw for ACQ Treated Wood
- Shop: Trailer Wiring
- Q&A: Screws Needed To Attach 5/8" Treated Plywood To Aluminum Snowmobile Trailer Frame
- Q&A: Can 18.5 x 8.5 - 8 Tires be Replaced with 215/60-8 Tires
on Accessories and Parts
