Can The Marlboro Continuous Hinge # MA74ZR Be Cut Down To Size

Question

Question:

I need 19 hinges 36” long. Can these hinges be cut in half to make two hinges?

asked by: Wes

0

Expert Reply:

Yes, the 3" Wide Continuous Hinge - 6' Long - 1/4" Pin Diameter - Aluminum # MA74ZR can be cut down to fit your needs. I just recommend first removing the pin and separating each part before cutting them. You'll be better off cutting it at the end of the hinge loops, like I have pictured below, instead of trying to cut through them.

expert reply by: Kevin C

0

Marlboro Hinge
(click to enlarge)

Answer 1

Hey Leif! I checked with Wells Cargo and the closest thing we have to what you described and they sell is the 3" Wide Continuous Hinge - 6' Long - Aluminum item #MA74ZR. This measures 6' long x 3" wide and each side of the foldable…

view full answer...

Answer 2

Marlboro piano hinges like the 3" Wide Continuous Hinge #MA74ZR you're looking at do no have weight capacities. Marlboro mentions that it will be up to the installer to determine if the hinge will be strong enough.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Can The Marlboro Continuous Hinge # MA74ZR Be Cut Down To Size

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching