Warranty for Dexter Trailer Hub and Drum Assembly

Question

Question:

what is the warranty the hub and drum assembly?

asked by: Bob

0

Expert Reply:

Hi Bob; the Dexter Trailer Hub and Drum Assembly # 8-201-5UC3-EZ falls under the Dexter limited 5-year warranty. This covers defects in material and workmanship.

expert reply by: Robin H

0

Answer 1

The inner bearings should be #LM48548 (1.375 inch inner diameter), outer bearing should be #L44649 (1.06 inch inner diameter) and the grease seal should be #58846. I would recommend you pull your bearings out to verify that but that SHOULD be what…

view full answer...

Answer 2

Your drum/hub that is the Dexter 8-147 part number should have an inner bearing #LM48548, an outer bearing #L44649, and a grease seal #58846. If this is the case then we do have some hub/drum assemblies that would work great for your application. The…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 7

The determine the correct replacement leaf spring on your 2021 Coachmen 259FKDS you'll need to lift your trailer frame so the spring is hanging freely and then measure from center-eye to center-eye, then for the equalizer you need to measure…

view full answer...

Answer 8

Hey James, you can go with a 4k axle leaf spring like the part #e22YR in place of what you have now while it has a slightly higher weight capacity it's not enough that it would create a harsh ride quality. This is a 26 inch long spring though so…

view full answer...

Answer 9

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 10

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 11

Hey Thomas, the most important factors for picking out a replacement leaf spring for a trailer are matching axle capacity and length. Getting the same amount of leaves in the spring pack is actually not a huge priority so I wouldn't worry too…

view full answer...

Answer 12

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Warranty for Dexter Trailer Hub and Drum Assembly

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching