Solution for Replacement Swing Away Tongue on ShoreLand'r Boat Trailer

Question

Question:

Hello, I have a shorelandr trailer and am looking to replace the swing away tongue. Is this something you could help with. SWINGTONGUE DISC 5IN M 69557 ASSEMBLY - 2007/4/17 - 2021/06/15

asked by: Brian

0

Expert Reply:

Hi Brian; a swing away tongue like the one you're referencing isn't something we carry and odds are you aren't going to find it anywhere. However, that doesn't mean I can't help you out. What you can use instead is the Fulton Fold-Away Coupler Hinge Kit. We have the following available:

-Fulton Fold-Away Coupler Hinge Kit for 3" x 4" Tongue - Bolt On - Up to 7,000 lbs # FHDPB340301

-Fulton Fold-Away Coupler Hinge Kit for 2" x 3" Trailer Tongue - Bolt On - Up to 5,000 lbs # FHDPB230101

-Fulton Fold-Away Coupler Hinge Kit for 3" x 5" Tongue - Bolt On - Up to 9,000 lbs # FHDPB350101

With the hinge you will be able to build a new tongue and bolt/weld-on a new brake actuator like the # T63FR you were looking at. This is designed for a 3" wide channel tongue and drum brakes. If you have disc brakes you can use the # DX56FR instead. Doing this also means you don't have to try to find an actuator that fits inside the old tongue since most of the time one that lines up doesn't exist.

expert reply by: Robin H

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

Hey Eddie, thanks for the pictures. From seeing that I can tell you have a 3,500 lb axle and the correct replacement hub would be the part #AKIHUB-545-35-G-EZ-K that you referenced which comes with new bearings and seal.

view full answer...

Answer 8

Hi Brian; a swing away tongue like the one you're referencing isn't something we carry and odds are you aren't going to find it anywhere. However, that doesn't mean I can't help you out. What you can use instead is the Fulton…

view full answer...

Answer 9

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 10

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Solution for Replacement Swing Away Tongue on ShoreLand'r Boat Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching