Grease Seal With A 1.5" ID And 1.98" OD

Question

Question:

Good Morning. I am looking for grease seals for the hubs on my boat trailer. I would like try the Spindo style of seal, with the stainless steel wear ring on the axle. I have an L44649 inner bearing, which would indicate that I need Kit #5, but it requires a 1-3/8 seal surface on the axle, and my axles have a 1-1/2 seal surface. are these type of seals available for a 1.5 ID and 1.98 OD application? Thanks,

asked by: Patrick W

0

Expert Reply:

The Grease Seals (pair) # RG06-020 and Grease Seal # 10-9 are the only grease seals that we currently offer with a 1.5" ID and 1.987 OD.

expert reply by: Kevin C

0

Answer 1

Hey Conner, for your CE Smith Kayak Trailer part #CE48810 the correct replacement seal would be the part #10-9.

view full answer...

Answer 2

You are correct, a double lip seal is better than a single lip. All things being equal I always recommend a double lip when available. Especially when the application is a boat trailer that will get submerged in water. The other difference between…

view full answer...

Answer 3

In order to find the correct replacement grease seal for a trailer axle you have a few options. The first and easiest option would be to crawl under the trailer and read the axle capacity off the tag on the center of the beam. The part #RG06-050 for…

view full answer...

Answer 4

It's not common for the spindle number to be printed anywhere on the axle. That said, if you're looking for new bearings/races and seals all you need to do is note the capacity or measure. The easiest method would be to crawl under the…

view full answer...

Answer 5

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

There is no exact way to determine the leaf spring length. The best way to determine the length for a replacement is by measuring the existing leaf springs. The hanger distance and shackle length can help you get a good idea, but you're looking…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Dexter axles are the industry leader in terms of overall quality. They are made in the USA and if you look around online or talk to people in the RVing community they general consensus is the Dexter axles are just better made overall and will be more…

view full answer...

Answer 10

Leaf springs typically have the part #stamped on the strap that holds the leafs together at one end of the shorter leafs, or it is painted on the concave side of the springs. The part number can then be used to determine the capacity of the springs.…

view full answer...

Answer 11

You are indeed right to think this way. When picking out the appropriate leaf springs for your custom built trailer you will want to choose them based on what the actual loaded weight of the trailer will be. Just make sure that the leaf springs have…

view full answer...

Answer 12

Hey Phil! Thanks for getting back to me with those measurements! We have a leaf spring that is an exact replacement but I am guessing it's the pricey one you referenced. It is the 4-Leaf Double-Eye Spring for 4,400-lb Trailer Axles - 25-1/4"…

view full answer...

Grease Seal With A 1.5" ID And 1.98" OD

Product Page this Question was Asked From

Continue Researching