Knapheide Truck Bed Box Replacement Key

Question

Question:

Hello, I wanted to ensure that this key would fit my lock boxs. it is a Knapheide truck bed box. it is a 1998 truck bed box with a serial number 65849TK and the lock says it is CH509. thank you

asked by: Adam A

0

Expert Reply:

Yes, I can confirm that the Replacement Key for UWS Toolboxes - CH509 item # KEYCH509 will fit your Knapheide truck bed box.

expert reply by: Jerred H

0

Kevin

6/16/2024

Got key code 6G4

Reply

Jerred H.

6/17/2024

@Kevin I am not familiar with that key code and can't find anything online. What is it on?

Reply

Answer 1

The Replacement Key for UWS Toolboxes #KEYCH509 will not say CH509 on it; however, you can simply use a permanent marker to write a key number on it, or put something like athletic tape on the key and write it on the tape if you are concerned the…

view full answer...

Answer 2

I checked with my technical contact at UWS to see if they made the truck cap tool box for Leer but I was not able to confirm that this was their OEM product. Still, it is quite likely that this part will work for you since the reference number…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

You're likely correct that this issue is with the truck, and I know that with the first generation of the factory integrated brake controllers on the Ram trucks there were a lot of issues like this that people have seen. You also mentioned that…

view full answer...

Answer 6

In order to determine which replacement key you will need for your UWS Truck Toolbox, you will need to get the code off of the lock core. I have attached a picture for you showing the location. The code should start with CH and followed by 3 numbers.…

view full answer...

Answer 7

As far as great heavy-duty mats that will fit with your clutch pedal on your 2019 Nissan Frontier king cab, I recommend the following mats: - WeatherTech Front Auto Floor Mats - Black #WT441761 - WeatherTech Front Auto Floor Mats - Gray #WT461761 -…

view full answer...

Answer 8

Key codes for UWS toolboxes usually include the letter prefix CH. Please refer to the photo that shows where to find this on the face of the lock. This photo happens to show a lock code CH510. I tried both of the codes you gave but neither seems to…

view full answer...

Answer 9

MaxxTow unfortunately doesn't offer replacement keys. If the box is locked, your best bet would be to drill out the lock and replace it with something like #UWSLOCKCH509. You will need to remove the cam lever from the existing lock and install it…

view full answer...

Answer 10

When choosing a jack for your trailer you will want to remember that the jack is not going to be lifting the entire weight of the trailer. You should choose a jack that exceeds the tongue weight of your trailer when it is fully loaded. The tongue…

view full answer...

Answer 11

In regards to a UWS Truck Bed Toolbox, if the box is locked and there is no key then you have two options. If you know the key number (it may be stamped onto the lock/latch) then you can order a replacement key like the Replacement Key for UWS…

view full answer...

Knapheide Truck Bed Box Replacement Key

Product Page this Question was Asked From

Continue Researching