Troubleshooting Norther Tool Ultra-Tow Aluminum 5' x 8' Trailer Wearing Inside Edge Of Tires
Question:
I need some advice. So here’s the deal. I have a Chesapeake Light Craft tear trailer mounted on a Northern Tool Ultra-Tow aluminum 5x8 trailer with about 9,000 miles on the trailer and tires. On inspection I noticed the inside tire tread on both tires is very worn and the outer sections hardly worn at all. The wear seems very smooth and even on both tires. At the truck scales it weighs about 800 lbs loaded, including with two bicycles. So do you have an opinion on what might be happening? I see you sell a Dexter 2200 lb bowed axle, T20BTR-EZ-7258, that seems like a possible fix. The trailer has 12 inch wheels and wondering if your hubs # AKIHUB-545-2-G-EZ-2K would be compatible? I’m open to all ideas.
asked by: Robert E
Expert Reply:
Based on the way the tires are rated, it sounds like the axle was over loaded, but I would imagine it has an axle rating of higher than 800lbs. Is there any chance your flipped the axle to get the axle underneath the springs to lift it, but did not weld on new spring seats?
That is typically the only time we see this kind of wear, as axles have an arch in them which becomes straight when loaded, but if the axle is flipped and new spring seats are not welded on then the arch will be pointing down the the tires will wear exactly how you mentioned.
If this is the case welding on new spring seats # TRSS175 would be the fix.
If you have not flipped the axle then it sounds like there is an issue with the axle causing the tires to not sit flat on the ground which is causing the uneven wear.
To fix this you will need to replace the axle, as there is not a way to correct the current axle.
The Dexter Trailer Idler Axle Beam with EZ-Lube Spindles - 72" Long - 2,200 lbs # T20BTR-EZ-7258 you were looking at may work as a replacement, but you will need to measure the hub face to hub face and spring center to spring center of your current axle. The # T20BTR-EZ-7258 measures 72" hub face to hub face and 58" spring center to spring center as shown in the included diagram. If this matches your current axle this would be a great replacement option.
The Trailer Idler Hub Assembly for 2,000-lb E-Z Lube Axles - 5 on 4-1/2 - Galvanized # AKIHUB-545-2-G-EZ-2K is compatible with the # T20BTR-EZ-7258 and works with 8" - 12" wheels so you will be able to reuse your wheels.
If you can let me know what size tires are currently on your trailer, I would be happy to make a recommendation for new ones since your current ones are worn.
I included videos of the products mentioned for you to take a look at.
(click to enlarge)
Products Referenced in This Question
Easy Grease Trailer Idler Hub Assembly for 2K Axles - 5 on 4-1/2 - Galvanized
- Trailer Hubs and Drums
- Hub
- EZ Lube
- L44649 / L44649
- Marine Grade
- For 2000 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- etrailer
more information >
Spring Seat for Typical 2,000-lb, Round Trailer Axles with 1-3/4" Diameter - Qty 1
- Trailer Suspension Parts
- Spring Seats
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Round Axle - 1-3/4 Inch
- TruRyde
more information >
Product Page this Question was Asked From
Dexter Trailer Idler Axle Beam with EZ-Lube Spindles - 72" Long - 2,200 lbs
- Trailer Axles
- Leaf Spring Suspension
- Standard Grade
- No Hubs
- 2200 lbs
- Spindles Only
- 58 Inch Spring Center
- 72 Inch Hub Face
- No Drop or Lift
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Article: Trailer Lighting Requirements
- Search Results: swivel jack
- Shop: RV Bearing
- Q&A: Replacement Handle for Northern Tool Ultra-Tow Trailer Tongue Jack
- Q&A: Upgrading Tires on Ultra-Tow 5 x 8 Aluminum Utility Trailer With Higher Speed Rating
- Q&A: Parts Needed to Add Electric Brakes to a 5x8 Aluminum Northern Tool Trailer
- Q&A: Adding Electric Brakes to Northern Tool UltraTow 5x8 Aluminum Frame Trailer
- Q&A: Are There Bearing Buddy Bearing Protectors for 5 x 8 Northern Tool Trailers
- Q&A: Replacement 4.80-12 Tires for Norther Tool Tag-Along Motorcycle Trailer
- Q&A: Can I Upgrade the 4.80-12 Wheels and Tires on a Northern Tool Ironton Trailer
- Shop: Chrome Lens Guard for 4" x 2" Trailer Side Marker Light
- Shop: Light Guard - Unpainted Steel for 440 Tail Light
- Shop: Timbren Axle-Less Trailer Suspension w/ Idler Hubs - Standard Duty - No Drop - 5 on 4-1/2 - 2K
- Shop: Combination LED Trailer Tail Light - Submersible - 7 Function - 14 Diodes - Driver Side
- Shop: CE Smith Trailer License Plate Bracket - Tail Light Mount - Aluminum Tread Plate
- Shop: CE Smith Trailer Tail Light Protector - 5-1/2" x 5-5/8" - Aluminum Tread Plate - Qty 1
- Shop: Stromberg Carlson Electric A-Frame Tongue Jack - 18" Lift - 2,500 lbs
- Shop: Trailer Hitch
- Video: Finding the Right Trailer Wiring Harness
- Search Results: trailer lights
- Article: Trailer Wiring Diagrams
- Video: etrailer VS Dexter Self Adjusting Brakes Comparison
- Search Results: trailer wiring
- Shop: Trailer Wiring
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: 25580
- Video: Measuring To Choose The Right Trailer Axle
- Article: Most Popular Wheel Bearings
- Shop: Brake Controller
- Search Results: trailer hitch
on Trailer Suspension Parts
