Recommended Trailer Bump Stop and Suspension Enhancement for Tandem Axle Trailer
Products Featured in This Question
Question:
I want to add bump stops to my LCI tandem axle suspension. What should the space be between axle and frame? My reason is to avoid spring over-load when ALL trailer wt is on ONE axle when backing over large hump into my storage spot, which causes tires on one axle to leave ground, or due to Andersen Rapid Jack use to remove a wheel.
asked by: Steve
Expert Reply:
The amount of space needed is going to vary depending on the spring that you use. If you use the Timbren Trailer Suspension Enhancement System Light-Duty Trailers 1,000 lbs # TTRA1702, those springs are only 2-3/4" tall so you can get away with fairly minimal clearance.
The other option would be the SumoSprings Trailer Helper Springs w/ Line Relocation Bracket - Single Axle - 3K to 5K - Underslung # TSS-106-40 for underslung axles or the SumoSprings Trailer Helper Springs w/ Line Relocation Bracket - Single Axle - 3K to 5K - Overslung # TSS-107-40 for overslung axles; these springs are 4" and 5" respectively and mount to the springs instead of the frame, so you'd want to measure from the spring pack to the frame to make sure you've got enough space for one of these kits to articulate fully. It sounds like these would be the best solution for your trailer if you can make them work, so you'll want to choose the appropriate kit based of whether your springs are mounted under or on top of your axle.
I've linked a great review video that explains all of this for you to check out.
Product Page this Question was Asked From
Timbren Trailer Suspension Enhancement System Light-Duty Trailers 1,000 lbs
- Trailer Suspension Parts
- Leaf Spring Enhancement System
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Rubber Springs
- 1000 lbs
- Single Axle
- Timbren
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Suspension Enhancement
- Q&A: What is Weight Capacity for Timbren Trailer Suspension Kit T92MR
- Shop: Replacement Gear Kit for Bulldog Sidewind Jacks w/ 12,000-lb Capacity
- Search Results: 28682
- Shop: Replacement Trailer Hub Bearing - 28682
- Shop: Buyers Products Weld-On Receiver Tube with 2-1/2" Hitch Receiver - 12" Long - 20K
- Shop: Timbren Rear Suspension Enhancement System
- Video: Installing the Dexter U-Bolt Kit on a 2018 Grand Design Reflection Fifth Wheel
- Shop: EZ Lock Trailer Coupler Lock for 1-7/8", 2", 2-5/16" Bulldog Collar-Lok Couplers
- Shop: Dexter Trailer Springs Over-Under Conversion Kit
- Search Results: sl58w
- Search Results: 28622
- Shop: Replacement Race for 28682 Bearing
- Video: What to Know About the Timbren Active Off-Road Bumpstops
- Search Results: mcl13r2b
- Search Results: trailer bump stop
- Search Results: ts10033b
- Shop: Lift Assist
- Search Results: 45791
- Video: All You Need to Know About the Dexter Trailer Springs Over-Under Conversion Kit
- Shop: Tonneau Cover
- Video: Complete Breakdown of the Dexter Trailer Springs Over-Under Conversion Kit
- Shop: Trailer Wiring
- Shop: Camper Tie-Downs
- Q&A: Should Bump Stops be Added to a Trailer when Using and Over/Under Conversion Kit
- Video: Dexstar Steel Spoke Trailer Wheel Spec Review
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Shop: Trailer Hitch
- Video: Picking the Right Front Suspension Upgrades for your Ford F-350
on Trailer Suspension Parts
