How to Remove Fulton Magnum Series Bolt-Thru Trailer Jack

Question

Question:

Need to know the steps in removing old trailer jack that is bolt on style

asked by: Dan B

0

Expert Reply:

The Fulton Bolt-Thru Swivel Marine Jack part # FXP10W0301 is held on to the trailer with a center bolt. It is also the pivot bolt. Use a box end wrench or a short wall socket to remove the existing bolt. It has pretty coarse threads and generally they come off pretty easily. If it appears rusty you may want to use a little bit of penetrating oil to make taking it off slightly easier.

expert reply by: Randy B

0

Answer 1

The roll pins that are used in jacks like the Fulton model on your trailer can be difficult to remove because they fit very tightly into place. I just recommend using a punch that is a bit smaller in diameter than the pin and then tap it with a…

view full answer...

Answer 2

Fulton bolt-through trailer jack #F1411300301 is the only Fulton jack that mounts using that 1 center bolt. Since your old jack was a Fulton it must either be this same jack or an earlier model but they use the same mount. The mount in question and…

view full answer...

Answer 3

The 1500-lb-rated Fulton Bolt-Thru Swivel Marine Jack #F1411300301 is a great choice to replace your Triton trailer's jack. You just want to make sure your jack mounting plate looks like part #P9012-00 which provides a bolt-thru installation. If…

view full answer...

Answer 4

The 60/40 axle placement formula is a great starting point and does take into account the tongue of the trailer from where the trailer sits on the hitch ball. Please keep in mind that this is a very basic formula or estimate for axle placement. For a…

view full answer...

Answer 5

I tried searching for the part number you listed but could not find anything with Fulton or online. However, if the mounting bracket on your trailer looks like the part #P9012-00 the Fulton Jack part #FXP10W0301 is going to fit and work well.

view full answer...

Answer 6

In order to determine which hubs you're going to need as a replacement you will need to pull the hubs to see what bearings will fit on your spindle; the bolt pattern is only part of the equation, but still helpful to know. To accomplish this you…

view full answer...

Answer 7

Thank you for the photo it was helpful in determining what you need. The replacement would be the Fulton Bolt-Thru Swivel Marine Jack #FXP10W0301 which has a bolt-through mount, 1,200 lb lift capacity and has bracket heights of 12-3/4" retracted…

view full answer...

Answer 8

A replacement for your Shelby 5138 is the Fulton Fas-Lok Coupler, 2" Ball, 3" Channel - 3,500 lbs #F223000301. This is a great quality coupler that is cost effective as you referenced. I've attached a review video of this product to…

view full answer...

Answer 9

In order to remove a welded-on trailer tongue jack you will need to cut off the old welds to release the mounting bracket. This can be done using an angle grinder. The jack can then be replaced with another welded-on option such as the Fulton Marine…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

How to Remove Fulton Magnum Series Bolt-Thru Trailer Jack

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching