Bearing Buddy Bra Size for Bearing Buddy that Measures 2.035 Inches

Question

Question:

Hello, The Outside Diameter of my bearing buddy is 2.035 in. Online it states that model 19B BRA MODEL: 19B Inner diameter of bra is: 2.125 in. possibly making a 19B too big. I am confused because the other questions here on E-Trailer say the Outside Diameter is 2.125 in. which could possibly fit depending on wall thickness. Please confirm if 2.125 in. is the Inner or Outer Diameter measurement? What Model Dust Cover should I buy? Thank You.

asked by: Monica D

0

Expert Reply:

Based on the diameter of the Bearing Buddy that you measured the correct replacement bra or cover is the part # BB19B you mentioned.

expert reply by: Jameson C

0

Answer 1

The ST185/80D13 trailer tire will be 10mm wider and the tire will go from 24 inches tall to 24-1/2 inches tall. Just make sure you have space to accommodate the extra height and width so that you do not end up with tire rub. Load range C tires have a…

view full answer...

Answer 2

For a Bearing Buddy that has an outer diameter of 2 inches you would want the cover part #BB23B.

view full answer...

Answer 3

A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

Hello Terrance, thanks for reaching out. You are wanting something to put on the 4" bumper on your motorhome, correct? If so, I recommend the Ultra-Fab Folding Spare Tire Mount for Trailers and RVs #UF15-954730. This will fit a 4" bumper…

view full answer...

Bearing Buddy Bra Size for Bearing Buddy that Measures 2.035 Inches

Product Page this Question was Asked From

Continue Researching