Why Choose a Powered Taillight Converter Over a Non-Powered Model
Updated 05/21/2025 | Published 07/01/2020
Question:
What dictates the need between using a powered Tail light convertor Vs a non powered?
asked by: Vincent W
Expert Reply:
There's a couple of factors that determine that. On older vehicles, very few vehicles needed a powered converter, because the vehicle's electrical system used a large enough wire gauge so that there was excess capacity in the vehicle's taillight circuits that could power both the vehicle taillights but also those of the trailer. However, once the vehicle manufacturers started going with smaller gauge wiring to save the cost of the copper plus the weight, many vehicles no longer had sufficient capacity in the taillight wiring system to power the vehicle and the taillight circuits.
Another important reason is that the powered converter provides circuit protection to the vehicle's electrical system. A short circuit in the trailer wiring could feed back into the vehicle's wiring system and possibly damage it. It's much easier and more inexpensive to find the short in the trailer wiring, repair it and replace the powered converter than it is to fix the wiring system of the tow vehicle.
If the option is available to go with a powered converter, I highly recommend going that route over a non-powered one.
Product Page this Question was Asked From
ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Vehicle End Connector
- Converter
- Universal Fit
- 4 Flat
- Plug and Lead
- Plug-In
- Hidden
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Curt Powered Tail Light Converter w/ 4-Way Flat Trailer Connector and Install Kit
- Q&A: Comparing Powered and Non-Powered Trailer Wiring Harnesses for a 2004 Nissan Xterra
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2019 Subaru WRX
- Q&A: Why is Trailer Wiring that Draws from Vehicle Battery Better than Non-Powered Kit
- Video: Best 2017 Subaru WRX Trailer Hitch Options
- Search Results: 1 7/8 ball
- Shop: EcoHitch Invisi Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Article: Determining Trailer Tongue Weight
- Search Results: 7 way wiring kit
- Shop: ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit
- Video: Best 2022 Honda CR-V Trailer Wiring Options
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Suspension Enhancement
- Shop: Vehicle Tow Bar Wiring
- Shop: Roof Rack
- Q&A: Trailer Hitch and Wiring Recommendation for a 2009 Honda Civic Coupe Si
- Video: Best 2009 Honda Civic Trailer Wiring Options
- Video: Installation: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector on a 2022 Honda CR-V
- Video: Curt Powered Tail Light Converter Installation - 2022 Toyota Sienna
- Shop: Base Plate for Tow Bar
- Q&A: Recommended Wiring Harness for a FWD 2024 Honda CR-V
- Q&A: Curt Wiring Harness Compatibility with FWD and AWD 2018 Honda CR-V Models
- Shop: Brake Controller
on Custom Fit Vehicle Wiring
Clay C.
4/21/2025
Is the powered unit more of a desired way to go if the output side is going to all LEDs and will be on all the time?