Replacement for Trailer Grease Seal SKF 21352

Question

Question:

I have a axle bearing seal and am looking for a replacement or replacement part number or numbers. I currently have a SKF 21352 seal. Do you sell these? Are there replacements? Is there a cross reference to another brand?

asked by: Jim P

0

Expert Reply:

The Trailer Grease Seal SKF 21352 has an I.D. of 2.125" and an O.D. of 3.371". The closest match we have is the Trailer Grease Seal part # GS-2125DL which has an I.D. of 2.125" and an O.D. of 3.376". Since these are grease seals, the .005" difference should not be an issue.

expert reply by: Conner L

0

Answer 1

The diameter of it is a pretty good way to determine the capacity. - 1,000-lb - 2,000-lb Axles: 1-1/2 inch - 1-3/4 inch diameter - 3,500-lb Axles: 2-3/8 inch diameter - 6,000-lb - 7,200-lb Axles: 3 inch diameter - 8,000-lb Axles: 3-1/2 inch diameter…

view full answer...

Answer 2

From what I was able to determine, your CR 21352 grease seal is a Chicago Rawhide 21352 and should be a double lipped seal with a 2.125" ID and 3.376" OD. To replace a seal of that size you'll want to use the #GS-2125DL, which has the…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement for Trailer Grease Seal SKF 21352

Product Page this Question was Asked From

Continue Researching