Instructions for Replacing Cover of Pace Edwards JackRabbit

Question

Question:

once I get the replacement cover, How do I get the old one out? is there a retractable spring that has to be rewound?

asked by: Jim

1

Helpful Expert Reply:

I spoke with Pace Edwards and they sent me an install instructions sheet for replacing the cover of a Pace Edwards JackRabbit Tonneau Cover. I attached the instructions to this page for you to check out. You do have to rewind the cover's spring but it's not like a garage door spring that is dangerous to wind.

expert reply by: Jameson C

1

click to enlarge

Answer 1

Typically if a Pace Edwards Retractable Tonneau Cover like the #311-M-BLFA18A44 is getting hung up it's with the railing and would require lubrication. The canister is a closed system so there isn't a good way to get into it and see if the…

view full answer...

Answer 2

I spoke to my contact at Pace-Edwards he said that when installing a replacement cover, like the Replacement Cover for Pace Edwards JackRabbit Hard Tonneau Cover #311-TRPT1472-2007, the typical way he recommends to keep the tension on the spring is…

view full answer...

Answer 3

In order to mount a set of cross bars onto a Pace Edwards Hard Tonneau Cover you would need to use the BedLocker part #311-BEFA05A28, the JackRabbit part #311-JEFA05A28, or the Full-Metal part #311-FEFA05A28 because these are the only options that…

view full answer...

Answer 4

If you are considering Timbrens like the #TDR1500DQ and the SumoSprings like the #SSR-307-47 for your 2022 Ram 1500 4x4, I recommend the SumoSprings #SSR-307-47. The SumoSprings will offer the same quality as the Timbrens in terms of suspension…

view full answer...

Answer 5

To remove the canister of the Pace Edwards JackRabbit Retractable Hard Tonneau Cover #311-JRFA18A44 you would need to remove the rails as well because they slide into the canister. The rails simply clamp onto the inner lip of your 2019 Ford…

view full answer...

Answer 6

There isn't a wire schematic available to the public for the Pace Edwards Bedlocker Retractable Hard Tonneau Cover #311-M-BLFA18A44, but it's just a power and ground wire combination so there really isn't much to it. I recommend checking…

view full answer...

Answer 7

The correct Replacement Operator Mechanism for your model 4751KS MaxxAir MaxxFan is part #MA10-20281K-1AF. If your fan lid is unable to open even manually, then this is the part you need to replace. The other part you referenced, #MA10A04751KS would…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Instructions for Replacing Cover of Pace Edwards JackRabbit

Product Page this Question was Asked From

Continue Researching