2019 Ram 2500 Pin Weight Capacity and Fifth Wheel Recommendation

Question

Question:

I have a 2019 ram 2500 crew cab short bed 6.7 Cummins. I am so confused about how much hitch weight I can have. Can you clear this up for me?

asked by: Randel L

1

Helpful Expert Reply:

I was able to find some information for you. On your 2019 Ram 2500 CC SB with the 6.7 cummins you will have a payload capacity of right at 2500 lbs. Payload can be used as the maximum allowable pin weight.

With that said the M5 Series 5th Wheel Trailer Hitch - Single Jaw - 20,000 lbs part # RP30928 that you looked at would be a perfect fit for your trucks payload. It offers a max 5000 lb pin weight and will work with trailers up to 20,000 lbs.

If you don't already have fifth wheel rails use Reese Quick-Install Custom Installation Kit w/ Base Rails for 5th Wheel Trailer Hitches part # RP50054-58 this will provide you with the connection point needed to set your fifth wheel into.

IF your Ram has the OEM puck system in it you will use Reese 5th Wheel Rail Adapter for Ram OEM 5th Wheel Towing Prep Package - 25,000 lbs part # RP30154 to give you that connection point.

expert reply by: Randy B

1

Troy W.

6/16/2024

Does the hitch add to the capacity to the pin weight. Also would adding air bags help increase weight?

Kevin C.

6/17/2024

@TroyW Anything in the bed from the rear axle back is going to count towards your pin weight, so this would include the 5th wheel hitch. Adding in air springs will not increase the capacity of the truck but would help you level the truck back out while hauling. This will help with braking power, overall handling, and keep your head lights pointed down at the ground instead of up at the car in front of you. If you're interested in adding some air springs to your truck I'd need to know the year/make/model of the and if it's 2WD or 4WD.

Answer 1

From Rep at PullRite, you will need to measure from the front edge of your king pin to the leading edge of the king pin plate to identify which you should use with your Rota-Flex 5th Wheel Pin Box and #LC328330. See the attached image I provided with…

view full answer...

Answer 2

Hey Randy, we have what you need but you will need to measure the width of your pin box to determine which capture plate you need. If it's 13-3/8 inches wide you'd want the part #PUL26RR or if it's 13-5/8 inches you'd need the part…

view full answer...

Answer 3

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

2019 Ram 2500 Pin Weight Capacity and Fifth Wheel Recommendation

Featured Help Information

Miscellaneous Media

Continue Researching