Bearing Buddy Bearing Protectors for 2.1 Inch Hub Bore Diameter

Question

Question:

Hi Im wondering what model of Bearing Buddy will fit a trailer with a bore size of 2.1 inches?

asked by: Alex

0

Expert Reply:

The closet option we have available to your 2.1 hub bore measurement is with the Bearing Buddy Bearing Protectors # BB2080 in Chrome or # BB2080SS in Stainless Steel (for superior corrosion resistance). These are designed to fit a hub bore diameter of 2.080 inches.

Since it's so close I recommend verifying your measurement with a digital caliper to get an exact dimension. I have attached a short video review that you can check out as well.

expert reply by: Chris R

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

Hey Barry, sure do! The seal that comes with the #DX87UR bearing kit is a 1.719" ID and 2.565" OD. We offer this seal individually as part #58846.

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 10

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Bearing Buddy Bearing Protectors for 2.1 Inch Hub Bore Diameter

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching