Will Camco Vented RV Bumper Cap Fit 3-3/4 by 3-3/4 Inch Inner Dimensions?

Question

Question:

Thanks for the info Jason. My bumper is not standard. I had it custom built to replace my old standard light-weight bumper that had structural damage. My bumper is 1/8" wall thickness, where standard is 1/16" wall. If I order this part on the basis that you say it will fit (tight), and then find it does not fit, can I return it at no cost to me? I'd rather not go through the hassle if there is a good chance it will have to be returned. Thanks

asked by: Joseph W

0

Expert Reply:

The Camco Vented RV Bumper Cap w/ Tether # CAM40324 will fit your standard 4 inch bumper that has inner dimensions for 3-3/4 inches by 3-3/4 inches nice and snug. The integrated fins will keep this cap secure to give you a clean finished look to your bumper and allow you to either store things within or keep things out.

expert reply by: Jason S

0

click to enlarge

Joe

3/29/2019

Thanks for the info Jason. My bumper is not standard. I had it custom built to replace my old standard light-weight bumper that had structural damage. My bumper is 1/8" wall thickness, where standard is 1/16" wall. If I order this part on the basis that you say it will fit (tight), and then find it does not fit, can I return it at no cost to me? I'd rather not go through the hassle if there is a good chance it will have to be returned. Thanks

Reply

Jason S.

3/29/2019

You obviously have a unique situation so I went to the warehouse to make the specific measurements for you so you can be confident about the fit. From outside edge to outside edge it is 4-1/8 inches square. From the farthest fin edge to edge it is 3-7/8 inches. From the smallest point to the smallest point not accounting for the fins it is 3-9/16 inches. The fins are a very sturdy plastic and not very flexible at all. They are designed to fit and grip so there is some give, but they are not flimsy. It is likely you'd need to sand or file the fins if you are planning on taking this cap in and out. If you will be leaving it in, you can most likely use a block and hammer to drive it into place without any modifications. I hope that info is helpful.

Reply

Answer 1

Hey James, you can go with a 4k axle leaf spring like the part #e22YR in place of what you have now while it has a slightly higher weight capacity it's not enough that it would create a harsh ride quality. This is a 26 inch long spring though so…

view full answer...

Answer 2

The newer Chevrolet and GM pickup trucks have a known power deficiency issue with the Furrion Vision S Wireless RV Observation Camera System w/ Side Marker Light Cameras #FCE48TASL-05. There is likely nothing wrong that you did, the problem is the…

view full answer...

Answer 3

The Progressive Dynamics Pure Sine Wave Inverter w/ Transfer Switch #PD64FR will require separate bus bars. Your AC in will go to your main bus bar and your AC out will go to your secondary bus bar. The items on your secondary bus bar will be powered…

view full answer...

Answer 4

I've attached the installation instructions for the Progressive Dynamics Pure Sine Wave Inverter w/ Transfer Switch - Remote - 2,000 Watts - 12V #PD64FR for you below.

view full answer...

Answer 5

A single yellow light on the Camco RV Power Defender, part #CAM55312 that you referenced indicates an open ground like you can see on the picture I attached. This is typically caused by a broken wire or bad connection in side the socket/plug of your…

view full answer...

Answer 6

The absolute best towing mirrors for your 2024 Ford F-150 are the K-Source Snap & Zap Custom Towing Mirrors #KS69NQ because they slip on over your OEM mirrors for a great fit that minimizes how much road vibration you see in the mirrors. We had…

view full answer...

Answer 7

Hey Edgar, I've attached a diagram below that should have all the measurements you need for the mounting brackets of the etrailer Scissor Stabilizer Jacks w/ Handle #TJSCHD-24-4. The brackets are about an 1/8" thick.

view full answer...

Answer 8

The Adco Tyvek Aquashed RV Cover part #290-52240 is what I recommend for a 2021 Winnebago Micro Minnie 2108TB. It's a great all around cover option. It has weighted buckles for easy installation and an integrated cinching system for a tight fit.

view full answer...

Answer 9

I attached a picture that details how to disassemble the Bulldog 12,000 lb jacks.

view full answer...

Will Camco Vented RV Bumper Cap Fit 3-3/4 by 3-3/4 Inch Inner Dimensions?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching