How To Properly Setup a Prodigy P2 Brake Controller
Question:
how do i know if my controller working properly. at low speed i can feel the thud from trailer when im applying the brake as if the trailer brakes are nor functioning. at higher speed it is ok.
asked by: Dani E
Expert Reply:
I would recommend you start over with your Tekonsha Prodigy P2 Brake Controller # 90885 and go through the setup process again so that it will be properly setup.
First step is to connect your trailer to your tow vehicle. Next, with the engine running, hold the manual lever full to the left and set the power knob to indicate approximately 6.0.
Now you will want to drive your tow vehicle and trailer on a dry, level, paved surface and fully apply the manual lever. If the trailer tires lock up turn down the adjustment knob. You will want to repeat the previous step until you set the brakes at a point that is right before tire lock-up. Finally, you will want to use the brake pedal to make a few low-speed stops to check the power level.
I attached installation instructions for this product and an FAQ article on brake controllers for you to check out also.

Product Page this Question was Asked From
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Splice-In
- Under-Dash Box
- Under-Dash
- Up to 4 Axles
- LED Display
- Single Trailer Only
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Shop: Brake Controller
- Shop: Suspension Enhancement
- Search Results: 7400ez
- Shop: Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Search Results: 118572
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Search Results: blue ox brk2022
- Search Results: 152789
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Video: DIY 2023 Ram 3500 Installation for the TorkLift SuperHitch Magnum Trailer Hitch Receiver
- Search Results: 56407
- Search Results: bx1139
- Search Results: bx88368
- Shop: Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Q&A: Assembled Height of Timbren Active Off-Road Bumpstops # TABSOSR
- Video: What to Know About the Timbren Active Off-Road Bumpstops
- Video: Review of ABS Fasteners Trailer Door Latch - Latches - ABS99FR
- Article: Troubleshooting Brake Controller Installations
- Q&A: Can Tekonsha Prodigy P2 Be Installed on 2011 Dodge Ram With Factory Integrated Brake Controller
- Video: Setting up the Hydrastar Electric Over Hydraulic Actuator Kit for Disc Brakes on a Flat Bed Trailer
- Video: Review of Hydrastar Brake Actuator - Electric-Hydraulic Brake Actuator - HS481-8067
- Video: Full Disc Brake Conversion Installation - 2020 Jayco Pinnacle Fifth Wheel
- Video: HydraStar Marine Electric Over Hydraulic Actuator Installation
- Q&A: Replacing the Factory Brake Controller on a 2011 Ram 3500 Laramie Longhorn Dually
- Q&A: How to Bypass Factory Integrated Brake Controller on a 2011 Ram 3500