Why The Axles Cannot Be Rotated and Original Spring Seats Be Reused When Flipping Trailer Axles
Updated 04/30/2024 | Published 09/20/2011 >
Question:
I was reading about the axle flip, which I am also looking into. I am trying to understand why the spring seats must stay on the bottom of the axle and new seats must be installed. Can you explain why we cannot just rotate the axle so the spring seats are on the top? I have everything apart, as I am replacing the springs and hubs, and it seems to me that I can just rotate the axle so the spring seats are on the top and tighten down the U-bolts in the opposite direction as well??? Thanks
asked by: Dennis
Expert Reply:
The reason you will not want to rotate the axle and just reuse the spring seat is because there is a bow to the axles that flattens out as the weight of the trailer is applied to the axle that if you rotated the axle, the bow would flip and the alignment of the trailer tires would be way off and you would encounter problems with how the tires wear and with overall trailer handling.
This is why the Dexter Trailer Springs Over-Under Conversion Kit # K71-385-00 that you referenced includes an additional set of spring seats for you to bolt onto the axles.
When lifting your trailer you need to keep in mind that the geometry of the trailer will change. You may encounter lower or heavier tongue weight, and/or the trailer may become top heavy, contributing to trailer sway and instability, especially when passing large trucks or in high winds. In these situations, it may require you to go with a weight distribution system with sway control, if you are not already using one. I have provided an faq link and a link to weight distributions systems for you to review.
I attached a picture of how the axles should look once flipped for you to check out.

Product Page this Question was Asked From
Dexter Trailer Springs Over-Under Conversion Kit
- Trailer Suspension Parts
- Alignment and Lift Kits
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- Round Axle - 3 Inch
- Dexter
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Winch Pulley Block with Hook, 10K
- Shop: Winch Pulley Block with Hook, 8K
- Q&A: Installation of Dexter Kit # K71-385-00
- Q&A: How Much Lift Does Installing an Over-Under Kit on a Trailer Give
- Shop: 6-Leaf Double-Eye Spring for 6,000-lb Trailer Axles - 26" Long
- Shop: Dexter Trailer Springs Over-Under Conversion Kit
- Shop: Dexter Trailer Axle w/ Electric Brakes - E-Z Lube - 6 on 5-1/2 Bolt Pattern - 89" - 6,000 lbs
- Shop: Dexter Trailer Springs Over-Under Conversion Kit
- Shop: Kenda K353 Bias Trailer Tire - 5.30-12 - Load Range D
- Search Results: trailer suspension parts
- Article: Trailer Wiring Diagrams
- Search Results: trailer leaf springs
- Article: How to Accurately Measure Trailer Leaf Springs
- Shop: Suspension Enhancement
- Video: All You Need to Know About the Dexter Trailer Springs Over-Under Conversion Kit
- Q&A: Can I Use Heavier Rated Leaf Springs on Trailer Without Causing Damage
- Q&A: What is the Best Grease for Trailer Bearings
- Video: Complete Breakdown of the Timbren Axle-Less Trailer Suspension w/ Idler Hubs
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Search Results: trailer tires and wheels
- Shop: Brake Controller
- Q&A: How to Determine Hanger Spacing for Tandem Axle Trailer Suspension with 26 Inch Springs
- Video: Hands-On with the SumoSprings Trailer Helper Springs w/ Line Relocation Bracket
- Article: How to Raise Your Travel Trailer Height
- Search Results: trailer axles
- Video: 4-Leaf Double-Eye Spring for 4,000-lb Trailer Axles Spec Review
- Q&A: Determining the Correct Leaf Spring Length for Trailer
- Article: How to Tell the Weight Rating of a Trailer Axle
- Search Results: trailer hitch
- Q&A: Over-Under Kit, Shocks, and Upgraded Equalizer for Toy Hauler
Dan
4/30/2024
I have a dual axle trailer which looks just like the OEM setup, with springs on bottom of axle. I'd like to raise my trailer but am interested in flipping just ONE axle, not both. (Clearance for a dump conversion) Seems this would raise the trailer by about 2 inches instead of 4. The equalizer in middle would not ride level, but seems it should have plenty of articulation. Any reason this wouldn't work? Thank you!