What is the Correct Way to Jack Up a Boat Trailer to Change a Tire
Question:
I am looking for an hydraulic jack to lift my boat trailer and boat, when I get a flat tire. When you get a flat tire the distance from the axle and the ground is very short. I have a 3 tons 6.5inch tall jack that it fits under the axle when the tires are inflated, but when I get a flat tire it does not fit under.
asked by: Hector
Expert Reply:
It is not recommend to jack up a trailer by the axle. This may cause damage to the axle itself. It also puts too much stress on the leaf springs. Instead, you will want to place the jack under part of the trailer frame preferably next to the leaf spring hangers. This will give you more room to use a jack like the Powerbuilt Unijack part # ALL620470 which has a 4,000 lb capacity and offer up to an 18-3/8" lift. The jack also has a built in stand for safety as most jacks are not designed to bear a load for an extended period of time.
I have attached a review video of the above jack for you as well.
Product Page this Question was Asked From
Powerbuilt Unijack - 18-3/8" Lift - 4,000 lbs
- Automotive Tools
- Jacks and Jack Stands
- Bottle Jack
- 4000 lbs
- Powerbuilt
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: trailer tires and wheels
- Shop: Kenda Karrier S-Trail ST145/R12 Radial Tire w/ 12" Galvanized Spoke Wheel - 5 on 4-1/2 - LR D
- Q&A: Where to Source Bolts to Install Demco Actuator DM72VR
- Shop: Fulton XLT Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift - Black - 1.5K
- Article: How to Bleed Your Trailer Surge Brakes
- Video: All About the Demco Hydraulic Drum Brake Assembly
- Video: Review of the Demco Hydraulic Drum Brake Assembly
- Shop: Demco Hydraulic Trailer Brakes - Free Backing - Galvanized - Left/Right - 10" - 3.5K
- Video: Review of Performance Tool Automotive Tools - 12V DC Impact Wrench - PT27PJ
- Shop: Powerbuilt Unijack - 18-3/8" Lift - 4,000 lbs
- Shop: Mounting Bolts and Hardware for 10" Brake Assemblies
- Q&A: What Specific Bolt Size And Length Are Needed To Install The Demco Brake Actuator # DM72VR?
- Q&A: Bolt Pattern for Demco Hydraulic Brake Actuator DM72VR
- Q&A: Does The Demco Actuator DM72VR Require Two Or Three Bolts For Installation?
- Q&A: Replacement for Atwood 61101 Brake Actuator
- Q&A: Recommended Replacement for Atwood Surge Brake Actuator 85778
- Shop: Andersen Quick Tire Change Kit with Leveler and Chock
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized
- Search Results: 9~123
- Search Results: gooseneck hitch
- Search Results: trailer hitch
- Shop: Gooseneck Hitch
- Search Results: trailer jack
- Video: All You Need to Know About the Bulldog Round Jack
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Q&A: Trailer Wheel and Tire Recommendation for Size ST175/80R13
- Search Results: boat trailer jack
- Search Results: 14125a
- Video: In-Depth Review of the Easy Grease Trailer Idler Hub Assembly for 3.5K Axles
- Video: Changing Brakes Demonstration
on Automotive Tools
