Trailer Jack Recommendation for Kendon Motorcycle Trailer with Round Tongue

Question

Question:

Thank you for the quick response. Can you suggest one that has a whee

asked by: Marcelo

1

Helpful Expert Reply:

There is no bolt-on jack made for a round tube trailer frame since this would make securing the jack rather difficult; it would want to rotate around the frame tube whenever it was under load.

You will need to have some steel material welded to your frame to allow jack installation. You can use a pipe-mount type like Pipe Mount Swivel Jack # DL22685 which includes the weld-on pipe section.

expert reply by: Jameson C

1

Marcelo

2/16/2018

Thank you for the quick response. Can you suggest one that has a whee

Reply

Jameson C.

2/16/2018

For that you'd need the Bulldog Jack part # BD1541150301, the pipe mount # BD015279, and the wheel caster part # BDCP555.

Reply

Sam R.

5/29/2024

@JamesonC In the part numbers thread above, I can’t seem to locate pipe mount BD015279, is this item # still correct, or out of stock?

Reply

Jameson C.

5/29/2024

@SamR That part number is no longer available to us so we can't get it anymore.

Reply

See All (5) Replies to Marcelo ∨

Answer 1

Bulldog Side-Mount trailer jack #BD198250 comes with a foot plate as standard. Bulldog jacks like #BD1541150301 are also available without a foot to allow you to select one like #BD018564 or to use a wheel like #BD500245. Please do note that a jack…

view full answer...

Answer 2

I'm assuming you're speaking of an anti-rattle device. Many anti-rattle devices depend on the receiver tube to have a lip around it. The Roadmaster #RM-061 or the Brophy #RSCP are examples of this type. An anti-rattle device like the #63232…

view full answer...

Answer 3

You are correct that all bolt-on trailer jacks require a square or rectangular frame member for installation. There is no bolt-on jack made for a round tube trailer frame since this would make securing the jack rather difficult; it would want to…

view full answer...

Answer 4

There are some Dutton-Lainson trailer jacks that are made in the USA as well as a few that are not. Any jacks that we carry that are made in the USA have that as part of the description to help set them apart. Currently we have the following options:…

view full answer...

Answer 5

The weld-on bracket that comes with the Square Pipe Mount Swivel Jack w Footplate #TJDP-5000S-FLB measures 2-1/4" long and has 1-1/2" inner and 2" outer diameters. I've attached a dimensional photo as well as some videos for you to…

view full answer...

Answer 6

Per the manufacturer The Pipe Mount Swivel Style Trailer Jack with Foot - Topwind - 10 inch Travel - 2,000 pounds #DL22679 the inside diameter of the pipe that is part of the jack housing is 2 inches.

view full answer...

Answer 7

Dutton-Lainson does not give a separate holding capacity for their Pipe Mount Jack #DL22685. The Fulton Drop-Leg Stabilizer Jack #FSJ1-SJ2 is one of the popular options for your type of situation. Each of these have a 3,000lb capacity so with one on…

view full answer...

Answer 8

Hello Greg, I’m assuming the overall weight of your trailer is 7,000 pounds. In that case, you’ll just need something to handle the tongue weight of the trailer. Tongue weight typically falls between 10–15% of your overall trailer weight, which would…

view full answer...

Answer 9

Hi Kerry; the 339894 is actually still an active part. The correct replacement motor is the Replacement Electric Motor Assembly for Lippert Coach RV Steps #LC63BX which is the same as the 339894.

view full answer...

Trailer Jack Recommendation for Kendon Motorcycle Trailer with Round Tongue

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching