Bulldog 2-1/4" Long, Weld-On Jack Pipe Mount for 2-1/2" Female Mount and 5/8" Pin
(41 reviews)
Price: $15.31
In Stock
Bulldog 2-1/4" Long, Weld-On Jack Pipe Mount for 2-1/2" Female Mount and 5/8" Pin
Item # BD015279
Retail:$16.50
Our Price: $15.31
You Save: 7%
Orders above $50 qualify for Free Shipping
In Stock
- All Info
- Reviews (41)
- Q & A (30)
- Videos (1)
- Photos
- Why etrailer?
Bulldog Accessories and Parts - BD015279
- Trailer Jack
- Camper Jacks
- Mounting Brackets
- Pipe Mount
- Bulldog
- 2-1/4 Inch Pipe Mount
2" Diameter, male pipe mount measures 2-1/4" long and is designed to be welded onto your application. Pin hole diameter is 5/8".
Features:
- Tube welds onto trailer to provide attachment point for your pipe-mount swivel jack
- This male pipe pairs with female mount
- Pull pin (BD500231) is sold separately
Specs:
- Pin hole diameter: 5/8"
- Fits: 2-1/2" female pipe mount
- Dimensions: 2" tall x 2-1/4" wide
- See diagram below
Dimensional Information
0152790300 Bulldog Weld-On Tube Mount
Video of Bulldog 2-1/4" Long, Weld-On Jack Pipe Mount for 2-1/2" Female Mount and 5/8" Pin
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Bulldog Trailer Jack BD015279 Review
Today we're going to be taking a look at the weld-on male pipe mount for trailer jacks. This piece gets welded to the trailer frame and provides an attachment point for a pipe-mount swivel jack. The male pipe pairs with a female mount. This is going to fit a 2 1/2" female mount. It's made from a raw steel construction. It's a weld-on application. Few measurements to go through with you real quick, starting with the outer diameter.
We see that that's going to measure right on 2". Inner diameter's about an inch and a half, so that means that we have 1/4" steel. The length, that's going to measure right around 2 1/4". The diameter of each pin hole, each one's going to measure the same, it's going to be 5/8 of an inch in diameter. From the center of that pin hole to the edge of the mount is about 3/4 of an inch.
From the center of that pin hole to the edge of this side, it's going to be about an inch and a half. That's going to do it for today's look the weld-on male pipe mount for trailer jacks.
Customer Reviews
Bulldog 2-1/4" Long, Weld-On Jack Pipe Mount for 2-1/2" Female Mount and 5/8" Pin - BD015279
Average Customer Rating: 4.9 out of 5 stars (41 Customer Reviews)
2" Diameter, male pipe mount measures 2-1/4" long and is designed to be welded onto your application. Pin hole diameter is 5/8".
- BD015279
by: Jeff k.07/20/2021
After some delivery issues were resolved i am happy with the end result.this is a 2003 kendon 2 up motorcycle trailer. The manufacturer does not make a tongue jack for this model. I had a 3 x 3 x 1/4 angle iron welded to the top of the tubing junction. Then welded the mount tube for the jack to that. Assembly looks and works well. Of course it is removed when traveling.
- BD015279
by: Bill08/03/2021
Good products and fast service. When I need trailer parts, etrailer.com is where I go.
- BD015279
by: Roger03/17/2021
I own a small utility trailer maunufacturing business. Anytime i need a special piece i turn to etrailer. There parts are high quailty and inexpensive
- BD015279
by: Ralph04/21/2021
Working perfectly just what I wanted and needed for my trailer
- BD015279
by: Gabe A.03/25/2014
First off, I am super impressed with the support from etrailer.com. I was notified right away that all of my items were not in stock. As far as these mounts go, they work as intended and should last a lifetime. Price was lower than any other I found and they fit my ProSeries trailer jacks perfectly. I put them on a trailer for my quad that I also use for a shooting bench in remote areas. To get better ground clearance, I purchased these to keep the jacks attached to the trailer, but way up high so clearance would not be an issue on trails.
- BD015279
by: Tommy B.02/19/2015
Great part. Fits the Pro Series 10" lift 2,000 lbs jack (PS1401060303) perfect.
- BD015279
by: Bruce W.08/02/2011
Cequent and Bulldog made it pretty difficult to determine the correct tube mount for my Bulldog #178201 jack, but this is it. Well built, ready for welding. This is the exact same part as #BD500240, but cheaper because it is not retail packaged.
- BD015279
by: Allen F.05/06/2012
A insert for the trailer jack that i also ordered from etrailer.Much better than using thin wall pipe.Insert @ jack fit snug @ work great together. For my future needs i will definitely use { ETRAILER ] again.
- BD015279
by: Gary C11/22/2017
Purchased a Drop-Tail Trailer without a Trailer Jack. etrailer recommended the products, mailed them FREE & got everytrhing in TWO DAYS. Installed without any issues. Highly Recommend!!
- BD015279
by: dave p.03/04/2014
I ordered these as a second set--used on the trailer frame to stow the mounts.
- BD015279
by: Lisa @10/08/2020
Exactly what I needed for my Genie Tz50
- BD015279
Bobby R - 10/24/2017
by: Bobby R10/24/2016
Great quality and as described, very fast shipping and most of all about half the price of other sellers.
Comments
Working great. No problems at all.
Bobby R - 10/24/2017
- BD015279
by: Jesse07/12/2019
extremely, extremely, extremely, super great c/s w/ Katie !!!!!!!!! tk's katie, these items are exactly what I needed and wanted !!!!! a kazillion GOLD STARES and hats off to you !!!!!! More tk's than I can say ……… "GODs BLESSINGs", !!!!!!!
- BD015279
David R - 09/05/2017
by: David Richards09/05/2016
It is what I ordered and of good quality. Heavy enough to weld securely
Comments
All is good after a year. Holes are true and not wallered out.
David R - 09/05/2017
- BD015279
by: Cory A04/18/2015
Very good description of product. Excatly what I need for my car hauler trailer.
- BD015279
by: Dennis11/09/2017
Plan to use this for a New Holland 456 mower to replace the original jack stand. Looks tough enough to handle the job.
- BD015279
by: Mark06/26/2015
Product fits my jacks perfectly. I'll weld it on, clean it up and paint it.
- BD015279
by: Steve L12/11/2014
These mounts make my jacks multi-purpose. E-trailer is a great company--fast and friendly!
- BD015279
by: Chuck06/24/2019
Delivered quality parts, quickly
- BD015279
by: Randy06/04/2019
Quick ship! Worked great
- BD015279
by: Owen05/15/2020
Fast shipping, easy website to use and competitively priced
- BD015279
Jack - 12/31/2018
by: Jack12/30/2017
Quick service!
Comments
Very well. Thank you.
Jack - 12/31/2018
- BD015279
by: Bill C05/12/2020
The best people to work with AAAAAAA AAAAAAA+
- BD015279
by: Kim06/13/2017
Good products - No issues
- BD015279
by: Danny03/19/2020
Exactly what I needed and excellent qua lity
25
41
Show More Reviews
Ask the Experts about this Bulldog Accessories and Parts
- What Grade Steel is Used to Make Weld-On Jack Pipe Mount # BD015279I spoke with my contact at Bulldog about Weld-On Jack Pipe Mount # BD015279. It is ASTM A512 low carbon steel.
view full answer... - Pipe Mount Needed for 5K Bulldog JacksAttached is a link to our selection of Bulldog pipe mounts that you can filter through to find the correct one for your jacks. Unfortunately without knowing the model number of your jacks I wouldn't be able to give you an accurate answer. The titles of the jacks offer some insight into dimensions and there are diagrams on the products pages to help demonstrate as well. For example, the part # BD015279 is 2" tall x 2-1/4" wide, has a pin hole diameter of 5/8" for part # BD500231, and...
view full answer...![Image 1 for]()
- Weld-On Trailer Jack Pipe Mounts Types And FunctionsThe weld-on pipe mount you need for a jack depends on the size of the mount on the jack. For example, the jack mount you mentioned, part # BD015279, is a male pipe and designed to work with a jack that has a 2-1/2 inch female mount and uses a 5/8 inch pin. We do not sell the mount that is on the jacks. The mounts we offer are designed to be the mount that is welded to a trailer that the jack attaches to. I have attached a link to our product page for the weld-on mounts we offer...
view full answer... - Recommended Pipe Jack Mount 2-1/4" Long with 5/8" Pin HolesIt sounds like you are looking for the Bulldog Weld-On Jack Pipe Mount part # BD015279 which is 2-1/4" long with 5/8" diameter pin holes. It has a 2" diameter as well. I have attached our entire selection below as well.
view full answer... - Correct Mounting Bracket For Pro Series Round, Pipe-Mount Swivel Jack PS1401440303I have another option for you, but the Replacement Mounting Bracket # TJB-MB you were looking at will not work with your jack. For your Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate - Sidewind # PS1401440303 you will need the Bulldog 2-1/4" Long, Weld-On Jack Pipe Mount # BD015279. This will give you the weld on attachment point you are looking for. I included videos of the products mentioned for you to take a look at.
view full answer... - 2 inch Outer Diameter Pipe Mount for Trailer Jack that is 2-1/4 inch LongThe overall length of the # DL22670 that you referenced is 1-7/8 inches long. For a similar pipe mount that is 2-1/4 inches long and 2 inches in outer diameter we have the part # BD015279 which would be what you'd need.
view full answer... - Weld-On Jack Pipe Mount Recommendation for a12,000 lb Equipment TrailerI went out into our warehouse and pulled a Bulldog Round, Pipe-Mount Swivel Jack, part # BD178203, that has the same 2 inch inner diameter and 2.5 inch outer diameter pipe mount swivel jack as yours. I then test fit a Bulldog 2-1/2 inch Long, Weld-On Jack Pipe Mount for 2-1/2 inch, part # BD005024, and a Bulldog 2-1/4 inch Long, Weld-On Jack Pipe Mount for 2-1/2 inch, part # BD015279. I found that either will work dimensionally, the # BD015279 will fit on the inside and the # BD005024...
view full answer...![Image 1 for]()
![Image 2 for]()
- Recommended Swivel Jack for Round Tube Trailer TongueThere is no bolt-on style jack made for a round tube trailer frame since this would make securing the jack rather difficult. The jack would want to rotate around the frame tube whenever it was under load. Your only option is to weld a jack mount onto your round tongue. You can use a pipe-mount type like the Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 10" Lift - 2,000 lbs # BD1541150301. This will require the mount # BD015279 and caster wheel # BDCP555
view full answer... - Pipe Mounts for 5K Bulldog Square Trailer JackWhat you are describing is called a pipe mount for a swivel jack. We have some such as # BD500339. The inner tube diameter is 2 inches and it uses a 5/8 inch pin, # BD500231. If you need the other end that mounts to the trailer it is # BD015279.
view full answer... - Matching Male and Female Weld-On Pipe Mounts for Trailer Swivel JacksThe only square pipe mount we have is # BDPQM1900. It would be for if you already had jacks with the appropriate size female end (2-1/4 inch). What you can do is use round pipe mounts. You can use male end # BD015279, and female end # BD005024. Both of these pipe mounts use 5/8 inch diameter pins and the fit will be a little loose. Another option is to use # BD015273 with # BD015271. These will be a tighter fit but use 9/16 inch diameter pins.
view full answer... - Does Bulldog Jack Mount # BD015279 Fit etrailer.com Swivel Jack # TJP-2002S-BYes, the Bulldog 2-1/4" Long, Weld-On Jack Pipe Mount # BD015279 that you referenced is the correct dimensions to match the pipe mount of the etrailer.com trailer jack part # TJP-2002S-B that you also referenced.
view full answer... - Trailer Jack Recommendation for Kendon Motorcycle Trailer with Round TongueThere is no bolt-on jack made for a round tube trailer frame since this would make securing the jack rather difficult; it would want to rotate around the frame tube whenever it was under load. You will need to have some steel material welded to your frame to allow jack installation. You can use a pipe-mount type like Pro Series # PS1401060303 which includes the weld-on pipe section.
view full answer... - Male and Female Pipe Mounts for etrailer Square Pipe Mount Swivel Jack TJDP-7000S-BThe end that normally attaches to jack # TJDP-7000S-B is # TJP-OP58. It has an outer diameter of 2-1/2 inches and inner diameter of 2 inches. For a weld-on male end that has 5/8 inch pin holes to match the above female mount use # BD015279.
view full answer... - Additional Pipe Mount for Using Pro Series Trailer Jack Part # PS1401440303 on another TrailerWe do indeed have a replacement pipe mount for using your Pro Series Trailer Jack, part # PS1401440303. The replacement mount is part # BD015279, which is 2 inches and diameter and will accept the 5/8 inch pin that your jack uses.
view full answer... - How To Attach Bulldog Trailer Jack # BD1541150301 To TrailerThe item you selected, Bulldog Jack, Sidewind Swivel - 2,000 lbs, part # BD1541150301, requires the use of a pipe mount to be welded to the frame of your trailer. I contacted our representative at Bulldog, and he informed me that to mount part # BD1541150301, you will need the Weld-On Jack Pipe Mount, part # BD015279, which will need to be welded to your trailer frame. I would recommend having a trailer professional weld part # BD015279 on your trailer so that you can install the...
view full answer... - Mount For The Pro Series Round Pipe-Mount Swivel Jack # PS1401440303For the Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate - Sidewind - 15" Lift - 5,000 lbs, # PS1401440303, I reached out to the manufacturer and confirmed that you will want the Bulldog 2-1/4" Long, Weld-On Jack Pipe Mount for 2-1/2" Female Mount and 5/8" Pin, # BD015279. Cequent makes the Bulldog and the Pro Series Jacks, so don't let the manufacturer name throw you. This is the correct mount for the Pro Series Jack you referenced. If you want the pin, it is Replacement...
view full answer... - What Is the Inside Width of the Bulldog Replacement Pipe Mount for Swivel JackThe inside width of the u-bracket portion for the Bulldog Replacement Pipe Mount for Swivel Jack part # BD500339 is 2-1/4" which you can see in the photo below. I don't have any that are 2-1/2" so I'd suggest the Bulldog 2-1/4" Long, Weld-On Jack Pipe Mount for 2-1/2" Female Mount and 5/8" Pin part # BD015279.
view full answer...![Image 1 for]()
- How does the Bulldog Sidewind Jack # BD150415 SwivelThe Bulldog Sidewind Jack, # BD150415, requires the 2 inch pipe, # BD015279, to swivel. The pipe has 4 holes that are compatible with the 4 holes on the pipe extension on the jack and swivels from the towing position to lifting position with the included pin. I made a short video showing how this jack swivels for you.
view full answer...![]()
- How to Get a Round, Weld-On Swivel Jack with a Removable FootplateI have a solution for you. While we do not have a pre-built weld-on swivel jack with a removable footplate, this can be assembled together with the following pieces: 1) Bulldog Round, Pipe-Mount Swivel Jack, part # BD1541150301. It's a swivel jack with a 10" lift and 2000-lb capacity. 2) Pro Series Detachable Footplate w/ Pin for 2" Diameter Jacks, part # PS1400700340. It's a foot plate for 2000 - 5000-lb jacks. 3) Bulldog 2-1/4" Long, Weld-On Jack Pipe Mount for 2-1/2" Female...
view full answer... - What Pipe-Mounted 7000-lb-Rated Jacks Work With Bulldog Weld-On Pipe Mount # BD003155The Bulldog Weld-On Pipe Mount # BD003155 works with any jack that fits a 2-1/2-inch male pipe mount and takes a 3/4-inch pin. 7000-lb jacks that fits this type of mount are shown on the link provided. These include both top-wind and side-wind jacks. Note that these jacks all use a 5/8-inch diameter pin, not a 3/4-inch. The 5/8-inch pipe mount that fit these jacks is # BD015279. With this you can use Replacement 5/8 Pull Pin # BD500232. We also have one 8000-lb jack, Pro Series side-wind...
view full answer... - Is a Jack Available Without Foot or Wheel?It sounds like you are looking for a jack without a plate welded to the side, a weight capacity of 2,000 lbs and a has a tube with a 1-3/4" diameter. While we have jacks with some of those things, there are none with each, with the tube diameter being the issue. For example, the Bulldog Round, Pipe-Mount Swivel Jack # BD1541150301 does not come with a wheel and the pipe mount is sold # BD015279 sold separately, though the outer tube has a diameter of 2-1/4". The smallest jack without...
view full answer... - Pipe Mount Jack Recommendation for Trailer that Has Wheel Caster OptionFor the square jack part # TJDP-7000S-B that you referenced we do not have a wheel that will replace the foot. The reason is that the wheels have lower capacities around 1,200 lbs and this jack has a 7k capacity. If you wanted a similar option with a wheel you'd want the # BD1541150301 for a jack with the wheel caster # BDCP555 that you referenced. For the pipe mount you'd then want the part # BD015279.
view full answer... - Recommended 2,000 Pound Pipe-Mount Swivel Trailer Jack I recommend taking a look at the Bulldog Round Pipe-Mount Swivel Jack # BD1541150301. This 2,000 pound trailer jack features a tubular swivel design that will let you swing the jack up for travel and down for use. It has a 2-1/2 inch female pipe mount that is designed to be welded onto the trailer with a Pipe Mount like # BD015279. It has a pull pin diameter of 5/8 inches and a total lift of 10 inches. I have attached the written installation instructions along with a short video demonstration...
view full answer... - Can a Swivel Mount be Added to Square Direct Weld Trailer Jack # TJD-7000SSquare Direct Weld Jack # TJD-7000S will weld directly to the trailer frame. To make it a swivel jack you would have to weld on pipe mounts such as # BD015279 and # BDPG9810-00. Or you could go with jack # TJDP-7000S-B that already has the mount welded to the jack and includes the pipe that gets welded to the trailer frame. I have linked a video review of this jack for you.
view full answer... - How does the Bulldog Jack # BD1541150301 SwivelThe Bulldog Jack, # BD1541150301, swivels on a metal tube, # BD015279, that will need to be welded to your trailer frame. I made a short video showing how this jack swivels for you.
view full answer...![]()
- Extra Mounting Pipes for Additional Mounting Locations for the Pro Series 2,000 Pound JackI have confirmed with my contacts at Pro-Series, and the correct mounting pipe for the Pro-Series Jack # PS1401060303 is the Bulldog # BD015279. This mounting pipe is 2-1/4 inches long, and is compatible with 5/8 inch pins, like what is used on the Pro-Series Jack you are considering. This mounting pipe requires welding for installation, so please make sure that the areas that you are going to install this jack are appropriate for installing this mounting tube. It is also recommended...
view full answer... - Will Bulldog Swivel Jack Pipe Mounts # BD015279 and # BD005024 Work TogetherYes, Bulldog pipe mounts # BD015279 and # BD005024 are compatible with each other. I have included links to videos on both parts for you.
view full answer... - Availability of Jack Mounts for Trailer and Jack Side with Pin You could use the 2-1/2 inch male mount part # BD005024 with the 2-1/2 inch female mount part # BD015279 and then for a pin part # BD500231.
view full answer... - Recommended Trailer Jack With Mounting Point Under 2-3/4" WideSince you have only 2-3/4" between the coupler of your trailer and a steel beam I recommend the Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 10" Lift - 2,000 lbs # BD1541150301 which will only take up about 2-1/2" of space on the frame to mount. This jack has a 2000lb weight capacity and will be plenty since you mentioned it will only need to support around 200lbs. You will need the Bulldog 2-1/4" Long, Weld-On Jack Pipe Mount for 2-1/2" Female Mount and 5/8" Pin # BD015279 welded...
view full answer...
Do you have a question about this Accessories and Part?
Why etrailer.com?
At etrailer.com we guarantee:Highest quality accessories and parts for the best price.
Our Lowest Price Pledge ensures you will never overpay for the parts you need.Real product know-how.
We make sure that the products we sell are what we say they are, and that they work the way they are supposed to work. Get real advice from a real person who has the knowledge and expertise needed to solve your problem.Most detailed, accurate accessories and part information available.
Because we take providing accurate product information seriously, we take our own detailed product photos, demo videos and installation videos, as well as verify measurements, instructions, and vehicle fit information.Installations, made easy.
We love helping people and have the most highly-trained customer service, hands-on experience, step by step videos and installation instructions.Fast shipping.
Your order is automatically routed to get out of our warehouse and to your door as quickly as possible. Receive free shipping on orders over $99.Personalized service for life.
We provide one-on-one, personalized service from the ordering process through the life of your product.Trusted since 1946.
We've been serving customers since our parts store first opened in 1946 and continue to be recognized by our customers, our vendors and third parties for exceptional service.Returns Policy
Need to return an item? No problem. Please read our Returns Policy for more information.
Info for this part was:
Written by:
Lindsey S
Expert Research:
Michael H
Expert Research:
Jeffrey L
Updated by:
Laura H
Updated by:
Wilson B
Installed by:
Cole B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 800-298-1624
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.