Installation Torque Specs For Andersen Ultimate Connection

Question

Question:

What are the bolt torque settings

asked by: Dave L

0

Expert Reply:

The Andersen Ultimate Connection 5th Wheel Trailer Hitch System with Adapter - 20,000 lbs # AM3200 only has 4 set screws that require torque. According to the installation details from the manufacturer, the 4 set screws need to be tightened to 40 ft. lbs. of torque using a 1/4 inch allen wrench. I've attached the installation details for you which state to tighten the other bolts snug.

expert reply by: Jason S

0

Answer 1

In regards to the Andersen Ultimate Connection 5th Wheel Trailer Hitch System with Adapter part #AM3200, the four kingpin coupler set screws will need to be torqued to 40 ft. lbs. per the manual. The kingpin coupler will need to be center on the pin…

view full answer...

Answer 2

The remote you need for your Jenson JWM72A is in the Replacement Service Pack for Jensen RV Stereo Item #JEN55VR.

view full answer...

Answer 3

We have just what you need for a higher speed rated tire to replace what you have on your Haul-Master Super Duty Folding Trailer. The part #TT53012C is your current size of 5.30-12 and has a speed rating of 81 mph so we know it will fit your trailer…

view full answer...

Answer 4

It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 #LC304136 system. Below I've listed out the steps you'll need to follow and will allow you to use the auto leveling again. Zero Point Calibration The…

view full answer...

Answer 5

To know exactly what key will fit your enclosed trailer's access door lock we'll need to know the brand and the key code. For example, since you were looking at a Bauer door lock, if your key code was 357 then you could use the Replacement…

view full answer...

Answer 6

To answer your question, there are not left and right hand opening door latches. Something like the Global Link RV Entry Door Locking Latch Kit #295-000019 can be used on doors with either left-hand or right-hand side hinges by turning the latch kit…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Hello John, thanks for reaching out. Since your bed is shorter that 8' we do recommend using a sliding 5th wheel hitch for extra clearance on tight turns. So for your 2020 Chevy 2500 I recommend the following: - B&W Patriot 5th Wheel Trailer…

view full answer...

Answer 12

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Installation Torque Specs For Andersen Ultimate Connection

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching