Bolt Size Recommended For Channel Style Tongue Trailer Coupler Installation

Question

Question:

What size bolt should be used to bolt this to the trailer?

asked by: Andy

0

Expert Reply:

To mount the Channel Tongue Trailer Coupler - Trigger Latch - Bolt On # CT-5003-Z, I recommend using 1/2 inch bolts. The higher the grade, the stronger the bolt. I've attached the review video to help as you plan this installation.

expert reply by: Jason S

0

Answer 1

The lights will need to be replaced, we have some great options for this. The Optronics LED Combination Trailer Tail Lights part #TLL160RK looks to be a great match for your existing taillights and the Custer Trailer LED Clearance Identification…

view full answer...

Answer 2

We do offer a wide variety of replacement lights for trailer but since trailer manufacturers don't keep a record of what they use on trailers I would need some pictures of the lights you are wanting to replace along with some measurements so I…

view full answer...

Answer 3

The closest size we have to a 25.5" slipper spring is 24-5/8". Do understand that this may be the correct size for your application since as leaf springs sag and get flatter they also get longer in length. Also the amount of leaves a spring…

view full answer...

Answer 4

A larger trailer tire basically wins in every category like you mentioned. Less rolling resistance, less affected by bumps in road for smoother ride quality, and bearings/hub spins less so in theory less wear and tear. So as long as you have room for…

view full answer...

Answer 5

The distance between the mounting holes of the Dexter coupler part #DX56FR is 3 inches so it would bolt right up to your trailer. For a manual lockout you could use with this you'd want part #DX94FR. Standard brake line kits like the part #DM5424…

view full answer...

Answer 6

Hey John, thanks for reaching out. You will want to use some 1/2" grade 5 bolts and locknuts for mounting the Demco Channel Tongue Trailer Coupler #DM15945. Since the current coupler uses only 2 bolts, you will be fine to use two bolts with the…

view full answer...

Answer 7

I definitely understand how safety chain capacities and determining exactly what chain rating you need for your trailer can be a bit confusing. To keep it as simple as possible, safety chain requirements state that the breaking strength of EACH…

view full answer...

Answer 8

I would be happy to help you find the correct replacement springs for your Continental AWC11e Trailer, but unfortunately we do not have a break down of the specific components your trailer uses. To determine the correct replacement spring you will…

view full answer...

Answer 9

The 8 inch wheels that you have does make things a little more difficult, but we do have an option available. With that being said, I recommend going with the Timbren Trailer Idler Hub Assembly for 2,500-lb Axles - 5 on 4-1/2 - Qty 2 #TA88545-2.…

view full answer...

Answer 10

The Curt QuickPin No-Latch Trailer Coupler #C22CR is currently the only coupler we have that fits a 2" hitch ball, 2-1/2" tongue with the holes 1" on center from the top of tongue frame. The holes are also 3" apart on center…

view full answer...

Answer 11

The reason that 10 Gauge #10-1-1 or 12 Gauge #12-1-1 wire is recommended for 10" brake assemblies, like part #AKEBRK-35-SA, is because they pull more power than the lights on your trailer. I believe the green wire you are referring to carries…

view full answer...

Answer 12

It really depends on your setup, if the safety chain loops on your tow vehicle are spaced far apart then you will need more slack to make a tight turn then if they were closer together. What I would recommend you do is connect your trailer to your…

view full answer...

Bolt Size Recommended For Channel Style Tongue Trailer Coupler Installation

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching