Can Pack Em Wheel Tie Down Kit Fit Expanded Metal Trailer Decking

Question

Question:

my deck is expanded metal do u think i can use this

asked by: Jeff

0

Expert Reply:

If you came up with a backing plate to use on the other side of the expanded metal of your trailer deck the part # PK-WTD would work well. I wouldn't recommend attaching the tie downs directly to the expanded metal though.

expert reply by: Jameson C

0

Answer 1

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

Hey Jack, If you're talking about a transition plate then you'll want the etrailer Enclosed Trailer Transition Plate #e32JR. This can be installed on either end of the ramp to help make the transition onto easier or at the hinge of the ramp…

view full answer...

Answer 5

Yes, we do. What you are describing sounds like the Inner Frame Brackets for Under-Bed Rail and Installation Kit for Reese Elite Series 5th Wheel Hitch item #RP27FR. I have attached a picture below. These come welded to the frame exactly where you…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

Hey Pat, yes we sell replacement hardware for all of the hitches we carry including the part #75758 with the part #RHK. Transferring the hitch to a new vehicle?

view full answer...

Answer 9

Hey Bill, The Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box #GY48GR has an 18.08" measurement from the center of the coupler to the center of the first bolt holes. When switching to a gooseneck pin box from the Lippert Turning Point…

view full answer...

Answer 10

If your Turning Point pin box is locked out by install the two bolts in the back of it then yes, you can use a hitch like the B&W Companion Gooseneck-to-5th-Wheel Trailer Hitch Adapter #BWRVK3500. If you ever decide to remove the two bolts and…

view full answer...

Answer 11

Chucking and jarring while towing a 5th wheel trailer (or any trailer for that matter) is unavoidable because the trailer itself is not one piece with your vehicle. When your truck starts to move forward from a stop your trailer is still sitting…

view full answer...

Answer 12

Absolutely! The B&W Companion Slider Gooseneck-to-5th-Wheel Trailer Hitch Adapter #BWRVK3400 weighs in just under 280lbs, and the Custom Underbed Installation Kit for B&W Companion 5th Wheel Trailer Hitches #BWGNRK1020-5W weighs in at just…

view full answer...

Can Pack Em Wheel Tie Down Kit Fit Expanded Metal Trailer Decking

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching