How To Determine The Replacement Parts For Boat Trailer Hubs

Question

Question:

I have a 1997 Yacht Club trailer made by Hawkeye, model WC108, and it also states WC112. It is a single axel GVWR 1150. Max Load 1100. The bearings are destroyed and I cannot get a number without taking apart the other side. The hub has 5 lugs and it looks like an axel of just over an inch. Is there a hub kit for this or a set of bearings, seals, etc. THANKS

asked by: Dan B

0

Expert Reply:

Since there is no standard set of bearings for a trailer you will have to do one of two things. You can pull the opposite wheel and hub and check the bearings you have on that spindle. The numbers will typically be found stamped on the side of the bearings as shown in the attached photo.

If you cannot find the numbers you will need to use calipers like part # PTW80157 and take some measurements in the locations shown in the photo. You will also need to measure the inside bore of the hub on your trailer.

After getting either the numbers off the bearings or the measurements you can let me know and I will be glad to make recommendations that will work for you. We always recommend replacing parts on both sides of the trailer to make sure everything is operating evenly and working.

expert reply by: Jeffrey L

0

click to enlarge

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 3

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

Hi Hayden; that bolt pattern is really uncommon but I believe it can be found on some really old Airstream trailers. There are no modern replacements that will match. The best option is to replace the hub with one that has a common bolt pattern like…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 11

Hey James, you can go with a 4k axle leaf spring like the part #e22YR in place of what you have now while it has a slightly higher weight capacity it's not enough that it would create a harsh ride quality. This is a 26 inch long spring though so…

view full answer...

Answer 12

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

How To Determine The Replacement Parts For Boat Trailer Hubs

Product Page this Question was Asked From

Continue Researching