# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Excellent quality, fast shipping. Finding a metric ball for our international application was a bit difficult. We knew etrailer was the place to go for all things "trailer" related. Very happy with the purchase!
Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.
# 2
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.
Easy install, took around 30 minutes by my self to install. Hardest part of install was torquing the bolts ! Installed 13322 Class III Hitch - Gm 1500/2500 Pickup and Curt Class III Ballmount -2ball-2 Drop
# 3
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 6-3/4" Long - 3,500 lbs
Sturdy. Shipped quick.
The whole process was as painless as it could possibly be. After reviewing my choices on their website, I ordered the trailer hitch by phone. Cathy was knowledgeable and efficient and everything I need was quickly ordered. Shipping time was short and I was very satisfied with the packaging. The hitch itself looked great. Installation instructions were clear and it is easily a do it yourself project. I had a local garage install mine and it took less than 15 minutes. ($25). The only "problem" I had was that the receiver I ordered came with a lock pin so I did not really need the separate pin I ordered. However, it's always good to have a spare.
# 4
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
Excellent customer service & support! Bought for my 2013 Honda Fit and plan to trailer my Yamaha Tenere motorcycle around North America! Very happy with hitch.
Typical quality of...VERY good!! Lol. I've pulled my small mc trailer numerous times with this hitch and NO issues!!!
# 5
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
I am very pleased with the hitch, ball mount, and electrical package. All were easy to install if you follow the easy to understand directions. An added plus for putting one of these on a MINI is that the hitch can be hidden behind the "black plate/cover" that is on the rear bumper. It looks just like it came out of the factory except when to need to install the ball mount. The service has been outstanding. This is the place to go.
# 6
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
Works perfectly. Fast shipping. Very Satisfied.
Very pleased with etrailer. Very easy to order from website. Fast delivery, easy to install ,perfect fit . Thanks. .
# 7
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
This was the longest hitch ball mount I could find anywhere. I used it with a short extension for my 2021 T G so that I could open the back doors without hitting the trailer wheel crank. With my new trailer, Intact Flyer Discover, I don't need the extension and can still open the doors. Works well.
# 8
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
I have a custom made tow guard. The ball mount I have was too short to allow me to attach the tow guard to my new truck. I searched the web and found just what I needed at etrailer.com. It's the only site I found that carried the size I needed. The product fits my needs perfectly. I can now protect my boat from rocks and other road debris when towing. Thank you etrailer.com.
# 9
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
# 10
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Drawbar looks great and will be using in next two days. Thanks!
# 11
Curt Class II Drawbar - 5" Rise - 11-5/8" Long - 3,500 lbs
I was in need of a hitch higher than the standard 3 or 4 inch riser and spoke with Samatha B, after a couple of emails she found a 5 inch riser for my 1 1/4" receiver. Just what I needed and a happy customer. Received very quick and good sturdy quality. Thanks again!
3.5 stars. Product looks like it should perform as advertised, but it arrived with several chips in the paint. This is most likely due to improper surface preparation and cleaning before the powder coat was applied. As you can see in the photos, there is already some surface rust on some of the areas, including the hole for the hitch pin. Ultimately the paint will get scratched up from use, but it would be nice to see some extra attention to detail from the factory.
# 12
MaxxTow Adjustable-Height Ball Mount - 2" Hitch - 7-1/2" Drop, 6-1/4" Rise - 5,000 lb
As advertised and quick delivery, I am an Etrailer fan!
Strong and works perfectly!
# 13
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
I bought this on my knowledgeable brother's advice - he gave me the exact order number and link to buy from etrailer! I had it installed locally, without complications. I use my truck mostly to haul my horse or my friend's two donkeys in my 14-foot stock trailer. I have no complaints, the hitch does what it's supposed to do.
Easy install, everything included, and great instructional video. Worked out great for my RAV4.
# 14
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.
Fits perfectly. I just wish you would’ve sent a pin with it because I had to go chase that down and get an aftermarket one at Ace Hardware.
# 15
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
The one foot ball mount works great on a 2014 Chevrolet Silverado work truck(no lift kit). We use it for a one axle, lawn care/utility trailer. It is used at least half the work week and has held up for a year. It may not be a good choice for a heavier trailer, but at that point we would also purchase a 2500 truck too. The mount helps clear the jack when the tailgate is opened with about 2 inches to spare.
Great product for getting out past the tire carrier on a small SUV. Customer service was wonderful with great follow through and any assistance I needed I will definitely use etrailer agin
# 16
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.
Product is exactly as described on the etrailer.com website and measurements and dimensions fit perfect. Easy phone order process and prompt delivery, standard shipping arrived 3 business days after the order was placed. The extra long version of the ball mount makes it perfect for me to put on the bike rack while towing my horses.
# 17
Curt Class III Drawbar - 2" Rise - 4" Drop - 13" Long - 7,500 lbs
Haven't used it yet. I bought it because of CURT's quality. It was beat up in shipping though.
Exactly what I needed to extend the reach of the ball beyond my rear tire carrier WITHOUT losing any tongue weight capacity! I used mine for the 2" rise.
# 18
Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
My order was missing installation parts, but the etrailer team were quick to correct the issue. Even without a lift, I was able to install the receiver and brake light cable quickly, thanks to their extensive video libray.
I cannot emphasize enough how kind and thorough etrailer's customer experience team is. I originally (incorrectly) place an order for trailer parts that did not fit together, and etrailer took the time to review my order, identify the issue, call and email me to let me know, and place the correct order while over the phone. I am not an expert on any of these items so it is so unbelievably appreciated that they cared enough to check to see if I meant to order what I did. The delivery then arrive a day earlier than expected. What more could you possibly want from a customer service team? Thank you so much, etrailer!
# 19
Curt Ball Mount - 6" Rise, 8" Drop - 11-1/2" Long - 5,000 lbs
The team at etrailer relayed helped find the right solution. Using this ball mount fixed the height issue I had with my SUV not lining up with the trailer. Very grateful for their help.
Works great!! I always order from etrailer Customer service and fast delivery
# 20
Curt Fusion Ball Mount for 2" Hitches - 1-7/8" Ball - 2" Rise - 5,000 lbs
Exactly what i ordered and it came fairly quickly! Im very happy worh everything!
The parts were perfect and delivered right on time. Troy the rep I dealt with was awesome as he helped me find the correct parts and told me how to measure the correct height on my vehicle so I was able to order the correct trailer hitch receiver. Troy was a complete pleasure to work with. etrailer had the parts I needed at a great price. They also had a video that was perfect to show me how to install the parts. The only small issue was that the wiring kit was supposed to have a fuse for my car, but none was included. I don't think this was etrailer's fault since the package was sealed. It was not a big deal since it was easily obtained at an auto parts store, but it would have been nice to have the fuse included. Thank you etrailer for such great customer service!
Draw-Tite Ball Mount Review - 2013 Toyota RAV4
Today on our 2013 Toyota Rav4, we will be test fitting the Draw Tite Ball Mount with a 3/4 inch rise or 2 inch drop with a capacity of 7500 lbs., Part #2923. We will begin out test fit by getting our hitch height, this is the measurement from ground to the inside top edge of our receiver tube. So our Rav4's hitch height is about 13 inches. We will now take our ball mount install it in the drop position being sure to line up our pin holes and securing it with a pin and clip. We will not take a measurement from the ground to the top of our ball platform and this will be around 11 inches. Make sure to measure your trailer height when your trailer is level. Measure from the ground to the bottom of the coupler. If your measurement matches ours, this would be a correct fit for you. We will now turn our ball mount to the rise position.
Curt Tri-Ball Mount Review - 2013 Toyota RAV4
Today on our 2013 Toyota Rav4 we will be test fitting the Curt Tri-Ball Mount Hollow 2" Shank, Part #C45001. To begin our test fit, we'll measure our hitch height from the ground to the inside of the top receiver tube of our hitch. Our measurement here is about 13 inches. We will slide the shank of the ball mount into the receiver tube of our hitch, line up our pin holes, slide through our pin and secure it with a clip. When installed, the height of our ball mount will be equal to our hitch height. Make sure to measure your trailer height when your trailer is level. Measure from the ground to the bottom of the coupler. If your measurement matches ours, this would be a correct fit for you. By removing our pin and clip, we can rotate to the left exposing our inch and 7/8 inch ball.
Convert-A-Ball Ball Mount with 2 Inch Drop Review - 2013 Toyota RAV4
Today on our 2013 Toyota RAV4, we will be test fitting the Convert-a-Ball cushion ball mount for two inch hitches with three-quarter inch rise, two inch drop and a 10,000 pound towing capacity, part number amsc2. We will begin our test fit by getting our hitch height. This measurement is from the ground to the inside top edge of our receiver tube. It's about 13 inches. We'll install the ball mount In the drop position, sliding the shank of the ball mount into the receiver tube of the hitch, line up our pin holes and secure it with a pin and clip. To get our measurement, we'll measure from the ground to the top of the ball platform. It's about 11 inches. Make sure to measure your trailer height when your trailer is level.
Draw-Tite Ball Mount Review - 2012 Toyota RAV4
Today on our 2012 Toyota Rav4 well be test fitting the Draw Tite ball mount, part number 2923. The first thing we want to do is measure our hitch height and that measurement goes from the ground to the inside top edge of our receiver tube. Our hitch height measures about 13 inches. Keep in mind that this measurement will vary depending on the model of hitch installed, the tire size, or variances in the vehicle themselves. Next well fit the ball mount into the drop position. This ball mount provides a two inch drop so when we measure the height of our ball platform it should be two inches than our hitch height.
Convert-A-Ball Ball Mount with 4 Inch Drop Review - 2012 Toyota RAV4
Today on our 2012 Toyota Rav4 well be test fitting the convert-a-ball cushion ball mount, part number AMSC4. The first thing we need to do is measure our hitch height. Thats the measurement from the ground to the inside top edge of the receiver tube. Our hitch height measures about 13 inches. Keep in mind that this measurement will vary depending on the model of hitch installed, the tire size, or variances in the vehicle themselves. Now this ball mount offers a four inch drop or a two and three-quarter inch rise.
What our customers are saying:
"Easy place to shop. Fast delivery and great products. Very happy with my purchase."