Roadmaster 6-Diode Universal Wiring Kit for Towed Vehicles with Separate Lighting
Item # 154-792-118158
Our Price: $192.60
Confirmed to Fit
2013 Chevrolet Suburban
1500
2500
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
This item qualifies for Free Shipping
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (55)
- Q & A (0)
- Photos
2013 Chevrolet Suburban - Roadmaster 6-Diode Universal Wiring Kit for Towed Vehicles with Separate Lighting
- Diode Kit
- Splices into Vehicle Wiring
- Tail Light Mount
- Universal
- Roadmaster
Connect your towed car's lighting system to your RV's to get the brake lights and turn signals required for towing. Designed for use with Chevrolet Suburbans that have separate brake and turn signals. 4-Pole flat loop and wiring converter included.
Features:
- Connects your RV's tail, brake and turn signal lights to your towed vehicle's lighting system
- Designed for use on towed vehicles that have a 3-wire system (separate brake and turn signals)
- Prevents electrical feedback and the damage it can cause to your towed car's electrical components
- Includes tail light converter to adapt your RV's 2-wire system (combined brake and turn signals) to work with the towed car's 3-wire system
- Contains everything you need to wire your car for flat towing
- 6 Hy-Power diodes
- Tail light converter
- 30' Long strand of 4-wire electrical cord
- 6' Long cord with 4-way flat connectors - both vehicle and RV ends
- Ring terminal and wire connectors
- 3' Long split-wire loom
- Limited Lifetime Warranty
Specs:
- Max amperage: 85 amps
- Max voltage: 24 V
Note: If your RV has separate brake and turn signal lights, you do not need to install the included tail light converter. However, you will need to replace the 4-way vehicle-side connector with one that is capable of carrying the separate signals.
The diagram below shows the installation of the 6-diode tail light wiring kit on a towed vehicle (or dinghy) that has separate turn signals (typically amber) and red brake lights. This kit will most often be used with a motor home that operates off of a 2-wire system wherein the brake lights do the flashing for the turn signals. The included tail light converter (118158) is used to convert the combined brake and turn signal lights to separate ones to match those of your towed vehicle.
154 and 792 Roadmaster Universal Wiring Kit with 6 Hy-Power Diodes and 118158 Tow Ready Tail Light Converter
Installation Details
Customer Satisfaction Score:
87% were satisfied with this product
13% of customers were not satisfied
- etrailer mistake
- Wrong item was ordered
- Did not fit
Customer Reviews
Roadmaster 6-Diode Universal Wiring Kit for Towed Vehicles with Separate Lighting - 154-792-118158
Average Customer Rating: 4.8 out of 5 stars (55 Customer Reviews)
Connect your towed car's lighting system to your RV's to get the brake lights and turn signals required for towing. Designed for use with vehicles that have separate brake and turn signals. 4-Pole flat loop and wiring converter included.by: Chris B03/25/2015
Subaru Outback Wagon
In ordering the parts I got a little confused as to exactly which kit I needed. My motorhome has combined brake/turn signal lights & the car ('03 Subaru Outback) has separate brake/turn/parking lights. Thought I needed the 6 diode kit (which I ordered) until I had all the parts here & read through the instructions for the umpteenth time (BEFORE cutting anything) & then realized what they were doing. Turns out all I needed was the 4 diode kit. Sounds like there won't be any problems returning the unneeded parts since they were never installed. Great service there!
Took a lot apart in the back of the car because of the lack of space behind the tail light assemblies, but it all comes apart pretty easily. Also allowed me to route the wiring along side the stock harness. Have a bunch of 1/2" split loom here & used it.
Thought I would have lots of wire left over, but I actually had to splice 2 cut offs to make a jumper long enough to get from 1 side of the car to the other. Glad the car wasn't any longer & I didn't have to make up 2 jumpers as with some of the kits!
Hardest part was finding a hole in the firewall & getting the harness routed under the dash so as to not tangle with the pedals, etc. I just don't flex like I used to.
Everything works fine although it was NOT a "5 minute job".
by: Rich L.03/05/2013
Chevrolet Volt
The diodes and wiring are good and worked well. But the 118158 converter produced a 3.5 volt drop such that the brake lights were as dim as the tail lights. And when a turn signal was triggered the brake lights dimmed even further. I ended up stringing a separate brake wire through the car and re-wiring my truck with a 5-wire connector.
by: Jerry B.08/04/2013
2013 Honda CR-V
Prompt deliver of product. We haven't gotten this part of our project installed, we are still watching YouTube videos and other info on procedure. Had very little difficulties installing base plate on our 2013 CRV this should go well also. Our lights are a little more complicated but once we figure out how to actually wire to them every thing we've learned so far is very straight forward.
by: Christopher03/14/2018
2012 Ford Five Hundred
I used this wiring kit on a 2012 Fiat 500 Sport. All of the components worked as advertised and I am really pleased with the result. I used the 6 diode kit so the FIAT's turn signals would work the same when it's being towed as when it is driven.
This was my first light wiring kit installation and it was quite a challenge on the small FIAT to fish the flat cable from the rear of the car to the front. I ran it along the drivers side - over the rear wheel well, along the rocker panel, and up over the front wheel well. The wheel wells were the most difficult part of the job. Running the cable from driver's side to passenger side along the rear bumper and running it from the front wheel well to the front of the car and installing a connector were straightforward.
One problem I ran into is the female disconnect terminals supplied with the kit that are used to connect wires to the diodes anticipated a thicker wire (16-14 AWG) than what the FIAT uses. A quick trip to a close by big box store was all that was needed to find the same connectors for a thinner gauge wire (22-18 AWG). You still use the supplied disconnect terminals with the flat cable connections to the diodes.
by: Dale H06/26/2020
2013 Honda Fit
An ingenious system that enables a combined break and turn signal set up on your RV to properly operate the separate turn signal / brake setup of your toad. Beautiful!
Dale H.
6/28/2021
Have been using the brake and turn signal system for over a year now, and it is still working flawlessly!!
by: John J06/12/2016
Honda
I bought this wiring kit because I wanted to wire my 2013 Honda CRV myself. E-Trailer has a video that is helpful in its installation . What I later found out was you need to route the wires through some covers underneath the vehicle and unless you have some means to raise the vehicle pretty high that routing will be difficult. I went to the Honda dealer and several other auto places and no one would install this kit for me because of liability reasons so now I have a product of question. I ended up at a friends garage who had a lift and we routed the wire from side to side and from front to back in about 20 minutes. Once secured in place I took the car home to finish the diode installation. Using the video it was easy to install. The only problem I had was putting the rear tai lights back in. You will need the separate the diodes as the space between the body and light housing is very close. Other than that everything worked out well.
by: ALEX A11/08/2016
The wiring works great, I got more in the KIT than I could possible use and I am sure I had to pay for the extras, but I got what I needed and am very happy.
Alex A.
11/8/2017
it is doing great
by: Jean C07/24/2019
Honda Civic
The Roadmaster Wiring Harness was installed easily by our mechanic and works perfectly with our Civic and RV. I'm certain we will use etrailer.com for our new dinghy towing requirements!
by: Bill02/05/2018
Toyota Tacoma
I used the wiring harness on my Tacoma pickup in preparing to tow it behind our 40’ motorhome. The harness went on easily from the front grill to the rear lights, where I soldered and heat wrapped each connection. The instructions were ample and easy to follow.
It’s been a year since the installation, and the wiring has worked flawlessly!
by: Jerry07/29/2021
Ford Ranger
Install on a 2020 Ford Ranger. The product was excellent. The only problem I had was trying to remove the nuts holding the front bumper on. Ford has these bolts embedded in a hard plastic frame that spaces the three bolts on each side. In trying to remove the nuts I got them started then they would neither come on off nor reinstall. The nuts were spinning the bolts. After thinking about the fix I was in I decided to cut the factory bolts off and replace them with 1/2" x 1 1/2" bolts with fender washers. I tried a sawsall with a metal cutting blade and the bolts ate the teeth right off. I put on a Milwaukee thick metal cutting carbide tooth blade and that did the trick. Other than that, which is Ford's fault, everything went as the etrailer videos showed. If you are doing this make sure to spray the exposed bolt threads with WD-40 or something like before you try to remove the nuts.
by: David10/28/2017
2010 Suzuki Grand Vitara
A great product. Installed easily. Previous wiring experience would be good for somebody wanting to use this.
It has performed flawlessly over the past year. I’d recommend it.
David
10/28/2018
Fantastic. No problems at all. Works as required every time I plug in.
by: Ron B05/23/2017
2015 Fiat 500
The kit contained all you need to wire lights on a Fiat. The instructions were clear and concise. Excellent product and service as usual for etrailer.
Ron B.
5/25/2018
After one year this kit is still doing its job flawlessly.
by: Rich B.06/02/2012
2012 Kia Sportage
This harness was an excellent choice. It took about an hour and fifteen minutes to install. Everything is spelled out for you in the instructions and if all else fails, watch the online video. The hardest thing was removing the tail light on the Sportage. I has a ball joint connection that forces you to pull harder than you think you should. I was afraid I would break the light. But it popped out and the rest was easy. Very complete and works great! The connections fit like factory. Very Pleased.
by: Dale05/06/2016
This is my second purchase of wiring kit for towed vehicle I have bought from Etrailer. I had some questions and Etrailer was able to answer every question I had. I will go back to Etrailer next time I need products such as this.
by: Danny07/05/2014
2013 Chevrolet Sonic
I found the product to be of very high guality. I did not supply pictures as I would need to remove my taillights again. I had to covert a motor home that did not have separate turn signals to a Sonic that did. The materials supplied allowed me to just that. I do have two other comments-The instructions showed the wires on the car on the passenger side which is opposite from the Sonic and most others I would think. I had to reverse my thinking to do the correct procedure. Also, could you not supply unit specific instructions if the towing vehicle lighting arrangement and the towed vehicle was identified. This would eliminate the extra parts that I did not need and help the customer complete the task. Other than that, very good product. I guess it is better to have extra parts ratter than not having enough but I just thought this might cut the cost for some applications.
by: John D07/29/2021
Was skeptical about using with led tail lights,but it all went well. The installation videos are spot on. After one year and about 12k miles traveled, no problems. My vehicle is a 2020 Ford Ranger.
by: James04/17/2021
Works as advertised. Design of these wiring kits is based on converting the common 3 bulb brake/turn signal systems to a 2 bulb system. This makes them unnecessarily complicated.
by: only1jerry11/05/2016
2005 Subaru Forester
I did a lot of research before buying. etrailer's prices and support are above average. I ordered the Roadmaster 913-1 baseplate, Falcon-2 towbar and 154 universal lighting kit. I was completely surprised by the fast shipping, all parts arrived 3 days before I expected AND the shipping was free!
Before I ordered I talked with etrailer support to ensure I ordered the correct parts. They were knowledgeable and helpful.
by: Wayne06/06/2015
Product arrived on time.Online videos very well done.Katie D. provided excellent customer service on all the parts ordered.
Wayne S.
6/11/2016
very happy with product still working without any problems
by: Dave G.07/28/2015
2008 Honda Fit
Very complete, hi quality, reasonably priced kit for lighting my "toad". If you have combined lights on your RV and separate lights (brake and turn) on your "toad", this is the kit.
by: Mike03/29/2017
Nice set up. Instructions were spot on. The hardest part of the installation was removing car interior panels to get to the wiring. Would definitely recommend this product.
by: Dale P03/20/2019
Ford
I ordered a towbar and accessories through the Internet site. It was very easy and also very informative. The supplies were ordered and I receive them in a couple of days. It was a great price and I did much research before I ordered. We are planning to install the towbar on our Ford C-Max and tow it with our phoenix cruiser 3100.
by: Kevin 04/27/2021
Contained everything I required except the independent stop light switch.
by: Greg R.12/18/2016
Customer service was the best. Product delivered as expected. I recommend this wiring package. My towing safety comes first and Etrailer delivered.
by: Denny K.07/14/2016
2014 Fiat 500
a little bit hard to get all wiring in, because I want the wiring not to be apparent and not exposed to harsh weather( snow, salt ,etc). But this setup is ideal, works perfectly and very quick when you connect your car the the motorhome.
25
55
Show More Reviews
See what our Experts say about this Roadmaster Tow Bar Wiring
- What is needed to Flat Tow 2001 Pontiac SunfireA quick search online for a copy of the owners manual states that the 2001 Pontiac Sunfire can be flat towed without modification if you have a four-speed automatic or a five-speed manual transaxle. To flat tow a vehicle, you'll need a hitch on the motor home, a tow bar, a base plate kit installed on the tow vehicle, a tow bar wiring kit so that the taillights on the vehicle work along with those on the motor home, safety cables and a supplemental braking system. Base Plate: I suggest...
view full answer... - Is a Brake Light Relay Needed with an Even Brake System on a 2011 Ford EdgeYour assumptions about the braking system on the 2011 Ford Edge are correct. An active braking system, also called a continuous power assist system, is different than what is on your vehicle. You can use the Even Brake # RM-9400 with the 2011 Ford Edge. You should not need a brake light relay if you are using a 6-diode kit that uses the vehicle wiring, # 154-792-118158. If you are using a 4-diode kit or any kit that plugs in line with the vehicle wiring then the brake light relay is going...
view full answer... - Recommended Items Needed To Flat-Tow 2013 Honda CR-VThere are five items needed when you flat-tow a vehicle. You will need base plates, a tow bar, safety cables, lighting for the CR-V, and most states now require a supplemental brake system. I will make some recommendations that will work with your 2013 CR-V. The base plates I recommend is the Roadmaster EZ4 Base Plate Kit, part # RM-521567-4. The tow bar I recommend is the RoadMaster Falcon All Terrain Tow Bar, part # RM-522. For safety cables I recommend part # RM-645. I recommend...
view full answer...
- How To Use a Blue Ox Rangefinder II Tow Bar On a 2013 Ford C-MaxYes, in order to reuse your Blue Ox Rangefinder II Tow Bar 4322 you will need the Blue Ox Rangefinder II or III Tow Bar to Roadmaster Base Plates Adapters part # RM-037. This adapter kit allows you to use the Blue Ox Rangefinder II Tow Bar with a Roadmaster Crossbar-Style Base Plate Kit. The correct Roadmaster Crossbar-Style Base Plate Kit for your 2013 Ford C-Max is part # 524432-1. There are not any mounts available for the Blue Ox Rangefinder II Tow Bar to use with a Blue Ox Base Plate...
view full answer...
- 2 Wire to 3 Wire Tow Vehicle Taillight Adapter for 2006 Chevrolet ColoradoYou definitely can use the 4 diodes you purchased, # 48955, to wire your 2006 Chevrolet Colorado to be towed behind your Motorhome. Along with the connector you purchased and the diodes you will need an appropriate length of Bonded 4 Wire, # 16-4B-1. I would recommend about 30 feet. When wiring the taillights your brake and turn signal will use the same filament in the brake light bulb with a 4 diode kit. I have added a wiring diagram for you to make the process easier. To eliminate running...
view full answer...
- Tow Bar Wiring Needed For 2000 Toyota RAV4The Hopkins Plug-N-Tow Wiring Harness # 43455 provides a 4-way flat trailer connector at the rear of the RAV4 for towing a trailer with the RAV4. This wiring harness is not designed to work when towing it behind a motor home. Since we do not have a custom flat tow wiring kit for the 2000 RAV4, the easiest way to provide lighting on your RAV4 when towing it behind your RV is to use a removable lighting kit. I recommend the Heavy-Duty Magnetic Tow Lights # TL21RK. These magnetic lights...
view full answer... - Recommended Flat Towing Components For 2007 Honda FitHonda states that the Honda Fit should not be flat towed, however, it is possible and there are many people that flat tow their Honda Fits. According to our flat towing authority, to be able to flat tow your Fit, you will want to follow the emergency towing instructions found in the owners manual. Honda lists specific procedures and restrictions, so it's important to follow those procedures and restrictions. If any damage were to occur due to flat towing, the warranty would be voided by...
view full answer... - Parts Needed To Flat Tow a 2015 Ford Fiesta Behind a Motor HomeA plug in tow bar lighting system is not available for your 2015 Ford Fiesta but there are other options that will work. You could use a magnetic light kit, # RM-2120, a bulb and socket kit, # RM-155, or a diode kit, # 154-792-118158. The magnetic light kit will be the most cost effective option and the least permanent. The diode kit is the most involved of the installations and requires splicing into the vehicle wiring for installation. The bulb and socket kit bypasses the vehicle wiring...
view full answer... - Tow Bar Wiring Kit for 2004 Chevrolet Malibu Classic Your 2004 Chevrolet Malibu Classic can indeed use the universal tow bar wiring/diode kit you referenced, Roadmaster part # 154-792-118158. This kit will require cutting and splicing of your vehicle wiring. An alternative is the Roadmaster Tail Light Wiring Kit with Bulbs # RM-155. This is a completely independent wiring kit that does not splice into or affect your vehicle's wiring. Its installation requires you to drill holes in each tail light housing to enable installation of the included...
view full answer... - 7-Way to 4-Way Round Wiring Adapter to Flat Tow a 2001 Honda CR-VWe do indeed carry a 7-Way blade style to 4-Way round adapter. It is # HM47043. This is a coiled cable that can stretch to 8 feet long. The 7-Way end plugs into the RV and the 4-Way end to the vehicle. The diode kit you mentioned is # 154-792-118158. For a 4-Way receptacle to mount on the front of the CR-V use # PK11410. It looks like you will have to pull fuses to flat tow the CR-V. Consult the owners manual to confirm. To avoid having to pull a fuse every time you can install a fuse...
view full answer... - Troubleshooting Tow Bar Wiring, Toad Vehicle Left Turn/Stop Not FunctioningIt sounds like the problem is the ground of the left stop/turn light you have on your RV. If this circuit has a weak ground or signal it will prevent the toad's taillight from functioning as well. Check the circuit on your tow vehicle for a weak ground or possible shorts and fix as necessary. Once you get the tow vehicle's taillights working again the toad vehicle's should work again. Check all connections between the tow bar lighting and the factory taillight circuits on the tow vehicle...
view full answer... - Recommended Tow Bar Wiring For 2015 Ford ExplorerWe do offer tow bar wiring that is designed to fit the 2015 Ford Explorer. I recommend the Roadmaster Tow Bar Wiring Kit, part # 154-792-118158. This kit is designed to work with your 2015 Ford Explorer with the separate lighting system. This kit includes the converter that will adapt an RV 2-wire system to work with the Explorer separate lighting system. I have attached a wiring diagram you can check out. I have also attached a link to an installation video for this kit. It is on a different...
view full answer...
- Using a Roadmaster Falcon 5250 Tow Bar to Flat Tow a 2010 Honda CR-VBefore you tow the vehicle you will want to consult the owners manual for information on towing the vehicle. For the 2010 Honda CR-V, you will need to use Roadmaster base plates, # RM-521559-4, that you referenced. Base plates are vehicle specific so the # 199-5 base plates will not fit the 2010 Honda CR-V. You can use the Roadmaster Falcon 5250 tow bar with base plates # RM-521559-4. You can also use the Brake Buddy. In addition to the base plates, braking system, safety cables, and tow...
view full answer... - Can a 2011 Kia Sorento 4 Cylinder Flat Tow a 2008 Nissan VersaI have good news and bad news. First the good news. I can tell you the towing capacity of the 2011 Kia Sorento 4 cylinder. The bad news, it is not enough to tow the 2008 Nissan Versa. The Sorento has a towing capacity of 1650 pounds and a gross combined vehicle weight rating of 5534 pounds. The 6 cylinder Sorento has a capacity of 3500 pounds. The 2008 Nissan Versa has a curb weight of approximately 2700 pounds. This is more than a thousand pounds above what the Sorento can tow so you...
view full answer... - Will Blue Ox Base Plates Work with Aventa 7335 Tow Bar for a 2013 Chevy Captiva SportI spoke with my contact at Blue Ox and the older version of the Aventa tow bar is compatible with the base plates, # BX3332 for your 2013 Chevy Captiva Sport. In addition to the tow bar and base plates, you will also need safety cables if you do not already have some, lighting, and supplemental braking. For safety cables you can use # BX88197. The coiled design helps keep the cables off of the ground. For lighting if you will not be towing the Captiva Sport very often I recommend a simple...
view full answer... - Parts Needed to Flat Tow a 2008 Honda CR-V with a Stowmaster 5000 Tow BarRoadmaster Base Plates, # RM-521559-4, for your 2008 Honda CR-V are compatible with all Roadmaster tow bars including your Stowmaster. You will not need any adapters to use the tow bar with the base plates. If you do not have safety cables, you will need to add some. You can use coiled cables # RM-643. The coiled design helps keep the cables off of the ground. For lighting I recommend a simple magnetic kit, # RM-2120, if you will not be towing the CR-V often. For a more permanent solution...
view full answer... - Parts Needed to Flat Tow a 2001 Saturn Coupe SC01The Roadmaster EZ Base Plate Kit - Removable Arms # 52181-1 is confirmed to fit your 2001 Saturn Coupe SC01 and is compatible with the Quick Disconnects # RM-222 mentioned in your question and all Roadmaster tow bars. The Tow Bar Quick Disconnects are designed to work with the Roadmaster StowMaster, StowMaster All-Terrain or Falcon All-Terrain tow bars. If you have one of these tow bars then these parts will work great. If you do not yet have a tow bar, I recommend the Roadmaster StowMaster...
view full answer... - Install Video for Installing Diode Tow Bar Wiring Kit that Uses 6 DiodesThere is a version of the diode style tow bar wiring that we offer that uses 6 diodes and will activate dedicated brake lights with the part # 154-792-118158 which I attached an install video for on a 2008 Honda Fit for you to check out.
view full answer... - Parts Needed to Flat Tow a 2014 Kia Soul Behind a Motor HomeYou will want to consult the owners manual for your 2014 Kia Soul to determine if your specific model can be flat towed behind a motor home. There are 5 items that you will need to flat tow your 2014 Kia Soul: base plates, tow bar, safety cables, lighting, and supplemental braking. For base plates you can use # BX2726. For a compatible tow bar the Alpha is a popular option, # BX7380. It includes safety cables. You can also use the Adventurer, # BX7322, for a more economical option. It...
view full answer... - Recommended Wiring Harness to Dolly Tow 2008 Chrysler Sebring ConvertibleTo wire your 2008 Chrysler Sebring for dolly towing behind a motorhome I recommend installing a tow bar wiring diode kit like the Roadmaster 6-Diode Universal Wiring Kit, # 154-792-118158. I have attached a drawing that details the 6 diode installation for you. You will need a circuit tester like part # PTW2993 to identify the correct wiring circuits to splice into, and you will need to install a 4-Way wiring connector on your motorhome if it is not already equipped with this style of...
view full answer...
- Tow Bar Lighting Recommendation for a 2010 Yaris HatchbackWhile that is a keen observation, the trailer wiring on your motorhome would already have the signals converted to being combined like the industry standard calls for. For lighting you can use the diode kit, # RM-15267, and not have to worry about cutting into the taillight housing. This will splice into your taillight wiring to allow your tow vehicle to control the taillight assemblies of the towed vehicle. This comes with a round 6-way connector that you will install on the front of...
view full answer... - Roadmaster Base Plate Compatible with Falcon 2 and AdaptiveBoth the Roadmaster MX Base Plate Kit # 4427-3A and the XL Base Plate Kit # 4427-1A will work with the 2014 Ford Explorer both with or without adaptive cruise control. Both base plates are also compatible with your Roadmaster Falcon 2 Tow Bar # RM-520. If you don't already have safety cables, cables like # RM-643 are required when flat towing. Other components needed to flat tow are a wiring harness for the towed vehicle, like # 154-792-118158, and a supplemental braking system, like...
view full answer... - Tow Bar Wiring kit Recommendation For 2001 Chevrolet Tracker Towed By MotorhomeThe tow bar wiring I recommend for your 2001 Tracker is part # 154-792-118158. This kit includes the diodes needed as well as all of the hardware you need to install. I have attached a drawing you can check out that shows how this diode kit is installed. To connect the vehicle 4-way to your motorhome I recommend the Blue Ox 7-Wire to 4-Wire, part # BX88254.
view full answer...
- Parts Needed to Flat Tow a 1999 GMC Sierra 1500 4x4 Behind a Motor HomeThe Demco base plates # DM9518077 will fit your 1999 GMC Sierra 1500 4x4. You will also need a compatible tow bar, safety cables, lighting, and supplemental braking to flat tow your truck. For a compatible tow bar I recommend the Commander, # DM9511012. This tow bar is rated for 6,000 pounds and includes safety cables. For lighting you could use a magnetic kit such as # RM-2120. Or for a more permanent solution you could use diode kit # 154-792-118158 that splices into the vehicle wiring. And...
view full answer...
Do you have a question about this Tow Bar Wiring?
Info for this part was:
Test Fit:
Joe V
Test Fit:
Nicholas E
Test Fit:
Randy B
Expert Research:
Jackie C
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Adam R
Expert Research:
Jeffrey L
Video Edited:
Zack K
Video Edited:
Sue W
Written by:
Lindsey S
Updated by:
Adele M
Updated by:
Rachael H
Updated by:
Wilson B
Updated by:
Hannah L
Updated by:
Isabelle B
Video by:
Andrew L
Video by:
Alan C
Video by:
Chris R
Installed by:
Cole B
Installed by:
David F
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Jerry B.
2/2/2015
So far, so good. Weve only towed the car one way from KS to Fl. Everything working great. Thinking about adding a receiver hitch but, will take it to the dealer as we sold our farm, and our tools and have the grandsons arent available to do the hard work.