2010 Chevrolet HHR Trailer Hitch
2010 Chevrolet HHR Trailer Wiring
2010 Chevrolet HHR Brake Controller
2010 Chevrolet HHR Base Plate for Tow Bar
2010 Chevrolet HHR Vehicle Tow Bar Brake System
2010 Chevrolet HHR Vehicle Tow Bar Wiring
2010 Chevrolet HHR BOLT brand vehicle and hitch locks
2010 Chevrolet HHR Roof Rack
2010 Chevrolet HHR Trunk Bike Rack
2010 Chevrolet HHR Air Filter
2010 Chevrolet HHR Exhaust
2010 Chevrolet HHR Suspension Enhancement
2010 Chevrolet HHR Performance Chip Tuners
2010 Chevrolet HHR Vehicle Lights
2010 Chevrolet HHR Tire Chains
2010 Chevrolet HHR Fluid Filters
2010 Chevrolet HHR Vehicle Engine Heaters
2010 Chevrolet HHR Radiator Fan
2010 Chevrolet HHR Cabin Air Filter
2010 Chevrolet HHR Lift Assist
2010 Chevrolet HHR Floor Mats
2010 Chevrolet HHR Vehicle Covers
2010 Chevrolet HHR Bug Shield
2010 Chevrolet HHR Side Window Vents
2010 Chevrolet HHR Vehicle Seat Covers
2010 Chevrolet HHR Replacement Mirrors
2010 Chevrolet HHR Windshield Wiper Blades
2010 Chevrolet HHR Windshield Covers
2010 Chevrolet HHR Vehicle Air Mattress
Videos
for Chevrolet HHR Owners
Help Articles
Expert Answers
Yes, you will have to remove the front fascia, but not the bumper behind the fascia in order to install the Roadmaster XL Base Plate Kit - Removable Arms, part #3141-1, onto your 2010 HHR. To remove the front bumper, it looks like you will have to…
You are correct that the Blue Ox #BX1120 is confirmed for your 2003 Jeep Wrangler X model, as long as it has the double tube bumper. The Blue Ox #BX1126 is confirmed for 2007 - 2014 Jeep Wrangler, and Wrangler Unlimited without aftermarket bumpers,…
All of the mounting brackets and pins that you see in the product pictures for the part #BX1692 that you referenced come with the kit. The removable arms that attach to the base plate kit come with it as well.
I could not find your invoice based on your email to confirm, but you most likely have the Blue Ox Base Plate Kit - Removable Arms #BX1692 with a distance between brackets of 22 inches. I reached out to my contact at Blue Ox and was able to confirm…
If you wanted just the breakaway cable and switch for a Roadmaster supplemental braking system you could use the #RM-8603 for the cable and then part #RM-650898 for the switch.
For your Demco SBS Stay-IN-Play DUO Supplemental Braking System #SM99251, you can use the: -Replacement Cylinder Cable for Demco Stay-IN-Play DUO and Air Force One Braking Systems #DM56VR for a replacement. Attached are a couple of videos for you to…
Because the Brake Buddy uses power from the vehicle's battery to actuate, you will need to set up the charge circuit as directed in the installation instructions. The parts needed to accomplish this are included with the Brake Buddy.
Good news is yes, the Roadmaster Crossbar-Style Base Plate Kit #RM-521424-4 that you mention will work with just fine with your double-tube bumper, as well as your 1999 Jeep TJ. With that being said, in order to use the: -Roadmaster Falcon All…
To flat tow certain vehicles, the ignition might be in a position that would normally activate certain accessories on the vehicle that would drain the batteries and aren't necessary while towing. To avoid this, some manufacturers instruct you to…
The Brake Buddy Select systems like the 3 part #HM39524 draws power directly from your towed car's battery. To do this, the included wiring harness connects to your car's battery for the charge. Install the harness by routing the wire end…
The #RM-650898 is designed to wire to the black and white wires of the transmitter you sent in a picture of. It's odd yours had the connector cut off though. Essentially the switch connects the two wires which will activate the trailers brakes so…
Yes the Replacement Inner Arm for Roadmaster Falcon 2 and BlackHawk Tow Bars part #C000172 is a confirmed fit for the Falcon 2 5250 Tow Bar.