Vehicle Style: 6-3/4 Foot Bed Change
Fold-Up - Hard Cover Specs:
Features:
Get top-notch style and versatility with this all-aluminum tonneau. Quad-fold cover sits inside your vehicle's bed rails and secures upright for unrestricted bed access. Textured, black paint finish provides durability.
More Information >Fold-Up - Hard Cover Specs:
Features:
Solid Fold 2.0 tonneau features a durable tri-fold cover with a rail-free design, works with your existing 18" - 20" standard toolbox, and has an easy-to-use clamping system for installation and removal. Watertight seal against toolbox.
More Information >Fold-Up - Hard Cover Specs:
Features:
Tri-fold tonneau cover folds up to provide two-thirds or full truck bed access. Prop rods keep cover from coming in contact with cab. Cover sits 1-1/4" above bed rails. Shuts with the tailgate open or closed.
Installation Notes:
Clamp-on style rail system requires no drilling for installation
More Information >Videos
for Tonneau Cover
Help Articles
for Tonneau Cover
Expert Answers
for Tonneau Cover
The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.
view full answer...Hi Jeff; thanks for the question and sturdy is definitely a good word for the etrailer tonneau that fits your 2022 Ram 1500 with a 5-1/2 foot bed, the etrailer Hard Tonneau Cover #e35DR. It's made of a fiberglass-reinforced plastic which is…
view full answer...The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.
view full answer...The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.
view full answer...Your 265/70R17 size tire is around 31-1/2 inches in diameter. You want to make sure the tire cover you get is large enough and doesn't have to be stretched over the tire. I'd rather have one that's slightly loose than one that…
view full answer...The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…
view full answer...Actually our etrailer.com brand brake assemblies are rebranded AxleTek assemblies. So we have the 8k left and right assembly set #AKEBRK-8 which is most likely what you need but these are 12-1/4 inch in diameter by 3-3/8 inches wide and attach with a…
view full answer...Because the Retrax PRO MX Tonneau Cover #RT80467 for the 2019 Chevy Silverado 2500 covers the bed rails, you would not be able to use a ladder rack like the Thule TracRac #TH27000XT since that rack requires the use of the bed rails. The only tonneau…
view full answer...Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…
view full answer...Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake controller…
view full answer...There is a solution for you, but the lift kits you referred to such as #K71-725-02 will not work with welded on torsion axles. The best option is for you to simply remove your torsion axles and use the Timbren Axle-Less Trailer Suspension System…
view full answer...Yep, you're exactly right; the distance from the center of the hitch pin hole to the welded gusset is indeed four inches on the Curt Ball Mount for 2" Hitches #C45112. So if that's the amount you need for it to work without hitting the…
view full answer...Filter Products (6)
Contact and Help
What our customers are saying:
In these days of customer "no service" I am usually disapointed when doing business with people I don't know. It was refreshing doing business with you. I'm impressed!
Randy
Watkinsville, GA