Combined wiring system - brake and turn signals are sent along the same wire.
Custom Fit Vehicle Wiring Specs:
Features:
This 7- and 4-pole trailer connector eliminates the need for an adapter and allows you to tow a trailer with either a 7- or 4-pole plug. Socket connects to your vehicle's OEM wiring system and mounts with included bracket.
Installation Notes:
Product intended as a factory replacement harness or socket
More Information >Custom Fit Vehicle Wiring Specs:
Installation Notes:
For vehicles with factory tow package; may require additional components or may be used as a replacement harness
More Information >Custom Fit Vehicle Wiring Specs:
Plug-In Location:
Features:
Quickly and easily install this custom harness to get a 7-way and a 4-way trailer connector on your vehicle. Connector plugs into OEM tow package wiring harness - no cutting or splicing required. Weathertight seal deters damage from water and debris.
More Information >Custom Fit Vehicle Wiring Specs:
Features:
Quickly and easily install a 7-way and a 4-way trailer connector on your vehicle with this custom harness. Connector plugs directly into OEM tow package wiring harness - no cutting, splicing or tapping required.
Installation Notes:
For vehicles with factory tow package; may require additional components or may be used as a replacement harness
More Information >Custom Fit Vehicle Wiring Specs:
Features:
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into OEM tow package wiring harness - no cutting or splicing required.
More Information >Videos
for Custom Fit Vehicle Wiring
Help Articles
for Custom Fit Vehicle Wiring
Expert Answers
for Custom Fit Vehicle Wiring
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
view full answer...A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we…
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs…
view full answer...I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for…
view full answer...While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the…
view full answer...The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the…
view full answer...To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part…
view full answer...The OEM prep package consists of 4…
view full answer...The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x…
view full answer...Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be…
view full answer...