Anti-Sway Bars Specs:
Features:
Minimize sway and improve the stability and driveability of your truck. Solid, 7/8" chromoly sway bar provides improved handling and safety. Adjustable anti-sway bar lets you choose level of stiffness. Includes mounting hardware.
Installation Notes:
No drilling required for installation
Product designed for 2-Wheel Drive models
If your vehicle does not have factory end links, kit HE74SR will be required: sold separately
More Information >Anti-Sway Bars Specs:
Features:
Minimize sway and improve the stability and driveability of your truck. Solid, 7/8" chromoly sway bar provides improved handling and safety. Adjustable anti-sway bar lets you choose level of stiffness. Includes mounting hardware.
Installation Notes:
No drilling required for installation
Product designed for 4-Wheel Drive models
If your vehicle does not have factory end links, kit HE74SR will be required: sold separately
More Information >Anti-Sway Bars Specs:
Features:
Minimize sway and improve the stability and driveability of your truck. Solid, 7/8" chromoly sway bar provides improved handling and safety. Adjustable anti-sway bar lets you choose level of stiffness. For 2" to 4" lifts.
Installation Notes:
No drilling required for installation
Product designed for 4-Wheel Drive models
Product is designed for vehicles that have been lifted 2" to 4"
Product includes the required end links
More Information >Videos
for Anti-Sway Bars
Help Articles
for Anti-Sway Bars
Expert Answers
for Anti-Sway Bars
The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you,…
view full answer...For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…
view full answer...Yes, the Solera Slide Topper part #LCV000168106 is the correct fit for your flange width of 90-1/2 inches. This specific model has a box width range of 86 to 91-3/4 inches which is perfect for your width listed.
view full answer...The Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets #RM47MR typically comes centered and you would only need to make adjustments after installation and testing to see if it continues to pull. If you adjusted it all the way out to…
view full answer...When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…
view full answer...I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…
view full answer...The torque spec for the rear U bolts on your 2019 F53 motorhome are dependent on the size. If you have 3/4 x 16 u bolts (and used a 1 1/8" socket to remove the nuts) then they torque to 250 lb-ft. If the u bolts are 7/8 x 14 (and you used a 1…
view full answer...If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…
view full answer...The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…
view full answer...Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…
view full answer...On oil bath hubs the seals are different than standard grease seals. The correct replacement for what you have is #91030. Unitized oil seals like this have a part that stays fixed and a part that rotates with the hub for optimum leak protection. I…
view full answer...The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.
view full answer...Filter Products (6)
Contact and Help
What our customers are saying:
I like the easy of navigation through the site. It only took me a couple of minutes to place my order. Thank You I will shop this sight again in the future.
Kevin
Manchester, MD