Vehicle Suspension Specs:
Features:
Get improved handling with minimal sway and body roll. The StableLoad pads in this suspension enhancement kit feature quick-disconnects and a hinged design so you can easily return to your original ride. Specially treated drill bits included.
Installation Notes:
Drilling into the leaf springs is required, and specially treated drill bits are included, along with detailed drilling instructions
Product designed for vehicles with factory leaf springs and a lower overload spring
More Information >Vehicle Suspension Specs:
Features:
Get improved handling with minimal sway and body roll. The StableLoad pads in this suspension enhancement kit feature quick-disconnects and a hinged design so you can easily return to your original ride. Specially treated drill bits included.
Installation Notes:
Drilling into the leaf springs is required, and specially treated drill bits are included, along with detailed drilling instructions
Product designed for vehicles with factory leaf springs and a lower overload spring
More Information >Vehicle Suspension Specs:
Features:
Get improved handling with minimal sway and body roll for your vehicle. Stainless steel StableLoad pads feature quick-disconnects and a hinged design so you can easily return to your original ride. Specially treated drill bits included.
Installation Notes:
Drilling into the leaf springs is required, and specially treated drill bits are included, along with detailed drilling instructions
Product designed for vehicles with factory leaf springs and a lower overload spring
More Information >Vehicle Suspension Specs:
Features:
Get improved handling with minimal sway and body roll for your vehicle. Stainless steel StableLoad pads feature quick-disconnects and a hinged design so you can easily return to your original ride. Specially treated drill bits included.
Installation Notes:
Drilling into the leaf springs is required, and specially treated drill bits are included, along with detailed drilling instructions
Product designed for vehicles with factory leaf springs and a lower overload spring
More Information >Videos
for Vehicle Suspension
Help Articles
for Vehicle Suspension
Expert Answers
for Vehicle Suspension
For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the…
view full answer...Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…
view full answer...Hey Tarek, for your 2023 Ford Raptor I recommend checking out the Timbren Suspension Enhancement System #T75MR. This suspension enhancement system has a load leveling capacity of 3,000 lbs, will increase stability while reducing sag, and will install…
view full answer...The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…
view full answer...It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…
view full answer...Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…
view full answer...I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…
view full answer...What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…
view full answer...If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
view full answer...From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…
view full answer...I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be 3/8" shorter but that is still close…
view full answer...From our experiences the Harbor Freight trailers like yours have a hub bore that requires a cap or Bearing Buddy that measures 2.047 inches like the #BB2047 you referenced. We don't have a standard cap that fits this size so the Bearing Buddy is…
view full answer...