Replaces the 18:1 Venture motor and right angle driveshaft assembly on your Lippert Components electric above-floor RV slide-out. Includes both actuator and motor so that you can quickly get back to camping.Features: Replaces the 18:1 Venture motor and right angle driveshaft assembly on your Lippert Components electric above-floor RV slide-out Gear ratio: 18:1
Replaces the 24" actuator with 18:1 Venture motor on Lippert electric through-frame RV slide-out. Includes both actuator and motor so that you can quickly get back to camping.Specs: Actuator length: 24" Motor: 12V DC 9,500 RPM 30 Amp 18:1 Gear ratio Features: Replaces the Venture actuator with motor on RV slide-out For use on LCI electric through-frame slide-out units Includes 1 Venture actuator with motor Made in the USA
In search of a replacement motor for your Through-Frame Slide-Out? Look no further than the Venture 18:1 Actuator Motor. This dependable and durable motor will get your slide-out back in action and provide reliable operation for years to come!
Replaces the 32" slide-out room actuator on your Lippert through frame slide-out system. Includes actuator with 18:1 Venture motor for proper slide operation.Features: Replaces the 32" slide-out room actuator on your Lippert through frame slide-out system Includes actuator with 18:1 Venture motor Designed for 2" x 2" and 2-1/2" x 2-1/2" Lippert electric through frame slide-outs Helps support proper slide-out room movement Fits: Lippert electric through frame RV slide-out systems
Replaces the motor and actuator for your LCI Through-Frame Slide-Out. Includes both Venture actuator and high speed motor.Features: Replaces the motor and actuator for your LCI Through-Frame Slide-Out Includes both Venture actuator and high speed motor Specs: Length: Extended: 101-1/4" Retracted: 61" Motor dimensions: 6-3/8" long x 3-1/4" 9,500 RPM 30 Amps 18:1 Gear ratio Made in the USA
Replaces the actuator on your Lippert electric through-frame motorhome slide-out. Works with Venture motors (sold separately). 28" Stroke length.Features: Replaces the actuator on your Lippert electric through-frame motorhome slide-out Works with Venture motors (sold separately) Specs: Overall length: 38-1/4" Stroke length: 28" Diameter: 1-1/2"
Replaces the 18:1 gear set for your Venture motor for your Lippert RV slide out. Includes (1) 18:1 2nd reduction gear, (1) 18:1 clutch assembly, and 1 roll pin.Features: Replaces the 18:1 gear set for your Venture motor for your Lippert RV slide out Includes (1) 18:1 2nd reduction gear, (1) 18:1 clutch assembly, and 1 roll pin Fits: 18:1 geared Venture motors for Lippert RV slide outs
Replaces the motor assembly for your Lippert Components Venture high-speed slide-out motor.Features: Replaces the motor assembly for your Lippert Components Venture high-speed slide-out motor Gear ratio: 58:1
Replaces the motor assembly for your Lippert Components Venture actuator and high-speed slide-out motor (LC168956).Features: Replaces the motor assembly for your Lippert Components Venture actuator and high-speed slide-out motor (LC168956) Specs: RPM rating: 9,100 Gear ratio: 18:1
Need a replacement motor for your LCI Through-Frame Slide-Out? Look no further than the Venture 28:1 Actuator Motor. This dependable and durable motor will get your slide-out back in action and provide reliable operation for years to come!
Replaces the gearbox on Venture electric fifth-wheel RV landing gear assemblies. Easy installation. Aluminum construction.Features: Replaces a damaged gearbox for Venture universal-mount fifth-wheel RV landing gear assemblies Also works with most other brands of landing gear, including Atwood, Lippert, and Stromberg-Carlson Easy to install with minimal assembly Aluminum construction Quantity: 1 replacement gearbox
Replaces the landing gear follow leg assembly for your Lippert Components Venture 5th Wheel RV landing gear. Mounts to the inside of the frame rail. Standard length.Features: Replaces the landing gear lead leg assembly for your Lippert Components Venture 5th Wheel RV landing gear Mounts to the inside of the frame rail Easy to install Includes snap pin Specs: Length: Extended with drop leg: 68" Extended no drop leg: 52-1/4" Retracted: 32-3/4" Travel: 35-3/4" Drop leg length: 16"
Replaces the landing gear lead leg assembly for your Lippert Components Venture 5th Wheel RV landing gear. Mounts to the inside of the frame rail.Features: Replaces the landing gear lead leg assembly for your Lippert Components Venture 5th Wheel RV landing gear Mounts to the inside of the frame rail Easy to install Includes snap pin Specs: Length: Extended with drop leg: 68" Extended no drop leg: 52-1/4" Retracted: 32-3/4" Travel: 35-3/4" Drop leg length: 16"
Replaces the lead leg on your fifth-wheel RV's Venture motorized landing gear. Mounts to the outside of your RV's frame rail.Features: Replaces the lead leg on your fifth-wheel RV's Venture motorized landing gear Mounts to the outside of your RV's frame rail 29-1/2" Outer tube with press fitted cap
Replaces the landing gear follow leg assembly for your Lippert Components Venture 5th Wheel RV landing gear. Mounts to the inside of the frame rail. Standard length.Features: Replaces the landing gear follow leg assembly for your Lippert Components Venture 5th Wheel RV landing gear Mounts to the inside of the frame rail Easy to install Includes snap pin Specs: Extended length: 33-1/2" Retracted length: 21" Drop leg length: 17" Travel: 19-3/4" Distance between weld stops: Outside to outside: 21-1/2" Inside to inside: 19-1/2"
Replaces the landing gear lead leg assembly for your Lippert Components Venture 5th Wheel RV landing gear. Mounts to the inside of the frame rail.Features: Replaces the landing gear lead leg assembly for your Lippert Components Venture 5th Wheel RV landing gear Mounts to the inside of the frame rail Easy to install Includes snap pin Made in the USA Specs: Black sleeve length: 33-1/2" Travel: 19-3/4" Drop leg length: 21"
Replaces the follow leg on your fifth-wheel RV's Venture motorized landing gear. Mounts to the outside of your RV's frame rail.Features: Replaces the follow leg on your fifth-wheel RV's Venture motorized landing gear Mounts to the outside of your RV's frame rail Specs: Length: Extended: 33-1/2" Retracted: 29-1/2" Fits: RVs with Venture-style landing gear
Give your 5th-wheel trailer or camper some new legs! Upgraded motor works nearly twice as fast as the standard 80 RPM base model. Outer tubes are 29-1/2" long with 15-1/2" between weld stops. Total lift includes 16" of drop leg.Features: Replacement landing gear kit for a manual or battery-powered setup Components can replace most Lippert (LCI), Atwood, Venture, etrailer, or Pac-Rim parts Cross shaft extends to fit your application Manual hand crank (included) lets you operate in case of power failure Drop leg travel reduces time spent cranking, adjusting, or holding buttons Upgrade to plunger pins (LG-119113 - sold separately) for fast and easy deployment Toggle switch will be right at home with your current electrical setup Fuse-protected wires - won't interfere with your camper's electrical IP-rated - can be mounted safely near propane tanks Excellent stability and support Large, rectangular footplates minimize sinking in soft ground Durable, sturdy steel construction Corrosion-resistant black powder coat finish Bolt-on installation - uses your existing mounting brackets Weld stops are located on both sides of the legs - universal mount Hardware and additional mounting brackets are included if you need them Made in the USA Specs: Combined weight capacity: 6,000 lbs Total lift: 37" Screw travel: 21" Drop leg travel: 16" Overall outer tube length: 29-1/2" Extendable cross shaft: Minimum: 41" Maximum: 71" Footplate dimensions: 5" long x 7-15/16" wide RPM at full capacity (5,000 lbs, 30 amps): 150 90-Day warranty Measurements to Know When Replacing Your Landing Gear Distance between weld stops (inside to inside) Overall length of the outer tube, including the cap Each weld stop is typically 1" wide, so for your third measurement, add 2 inches.
Give your 5th-wheel trailer or camper some new legs! 19-1/2" inside to inside between weld stops. Includes manual crank and 1 motor, with room to add a 2nd one (sold separately).Features: Replacement landing gear kit for a manual or battery-powered setup Gearbox works with single- and dual-motor configurations Components can replace most Atwood and Venture parts Connecting cross shaft extends to fit your application Electric motor is an upgrade from manual methods Allows the lead and follow legs to work together at a faster rate Drop leg reduces time spent cranking, adjusting, or holding buttons Upgrading to plunger pins (LG-119113 - sold separately) would eliminate fiddling with cage pins Toggle switch will be right at home with your "current" electrical setup Fuse-protected wires - won't interfere with your camper's electrical IP-rated - can be mounted safely near propane tanks Excellent stability and support Large, rectangular footplates minimize sinking in soft ground Durable, sturdy steel construction Corrosion-resistant black powder coat finish Bolt-on installation - uses your existing mounting brackets Weld stops are located on the side facing toward your trailer frame - outside mount Hardware and additional mounting brackets are included if you need them Specs: Weight capacity: Single motor: 2,500-lbs per leg Dual motor: 5,000-lbs per leg Total lift: 34-3/4" Screw travel : 19-3/4" Drop leg travel : 15" Overall outer tube length: 33-1/2" Outer tube width: 2-1/2" Distance between weldstops: Inside to inside: 19-1/2" Outside to outside: 21-1/2" Rate of travel: 2-1/2" per minute Extendable cross shaft: Minimum: 41" Maximum: 72-3/4" 360 Watt DC motor Volts: 12 Amps: 30 Note: The distance between weld stops should match up with the mounting brackets already on your trailer frame.
3" Wide wobble rollers replace the worn-out rollers on your boat trailer's roller bunk. Ribbing provides extra traction for slippery hulls. Includes bushings for 3/4" or 1-1/8" diameter shaft on roller bunk.Features: Replaces 4 wobble rollers on the roller bunk assembly of your boat trailer Direct replacement for OEM rollers on LoadRite, Sealion, Venture, Calkins, Hawkeye, Karavan, and King Marine boat trailers Supports your boat, eases loading and unloading, and absorbs road shock during trailering Provides additional traction thanks to ribbed design Great for slick or slimy hulls Removable bushings ensure that rollers fit 3/4" and 1-1/8" diameter shafts Constructed of sturdy rubber with polypropylene plastic hubs Made in the USA Specs: Fits 3/4" and 1-1/8" roller shafts Roller dimensions: 5" diameter x 3" wide Inside hub width: 1-1/2"
Just the bones - replacement setup comes with everything but the electrical. Measures 15-1/2" between weld stops. 16" of drop leg makes up almost half of the total lift. Get your 5th wheel back into action!Features: Replacement landing gear kit for a manual or battery-powered setup Gearbox works with single- and dual-motor configurations Components can replace most Atwood and Venture parts Connecting cross shaft extends to fit your application Manual hand crank (included) lets you operate in case of power failure Drop leg reduces time spent cranking, adjusting, or holding buttons Upgrading to plunger pins (LG-119113 - sold separately) would eliminate fiddling with cage pins Excellent stability and support Large, rectangular footplates minimize sinking in soft ground Durable, sturdy steel construction Corrosion-resistant components Black powder coat finish on the legs Aluminum housing for the gearbox Built-in grease zerk makes maintenance easy Bolt-on installation - uses your existing mounting brackets Weld stops are located on both sides of the legs - universal mount Hardware and additional mounting brackets are included if you need them Made in the USA Specs: Combined weight capacity: 6,000 lbs Total lift: 37" Screw travel : 21" Drop leg travel : 16" Extendable cross shaft: Minimum: 41" Maximum: 71" Footplate dimensions: 5" long x 7-15/16" wide Handle dimensions: 29-11/16" long x 10-3/16" wide 90-Day warranty Note: The distance between weld stops should match up with the mounting brackets already on your trailer frame.
Filters
