The hydraulic bottle jack lifts, holds, and locks vehicles in place without jack stands. Properly fitting unibody framed vehicles, the Unijack is perfect for cars, crossovers, and small SUVs and trucks. 21" Lift range with 3 ton capacity.
These unique jacks extend from 11" to 17" and support up to 6,000 lbs each. Stackable design means that they take up less space when stored. For stabilizing only - do not use for lifting.
Minimize the amount of cranking needed to position your jack, and eliminate the need for wood or cinderblocks when storing your trailer. Jack stand provides a sturdy platform that evenly distributes your trailer weight.
Pull the front-facing plunger pin on this heavy-duty jack to release the drop leg for an extra 13-1/2" of lift. Get maximum lifting power in low gear and fast cranking in high gear. Sidewind crank (TJD-12000-HD) sold separately.
If you off-road but space is at a premium, the Tallboy is a compact bottle jack that can still create some serious lift. The oversized base plate gives you a solid foundation on the trail. And it only takes up about one cubic foot when stored.
Base pad replaces the bricks and blocks normally needed when positioning your trailer jack. 8" Tall pad works as a jack stand to support your trailer's tongue or stabilizer jack.
Hey Mike! The Power Mountain Tallboy Off-Road Bottle Jack #PM34FR can be stored in that manner (with the oil plug facing up), but my contact at Power Mountain stressed that it should only be done for a short period of time, so I recommend setting it…
Hey Todd! At the lowest setting, the saddle of the Power Mountain Tallboy Off-Road Bottle Jack #PM34FR sits at 14" and the top of the saddle arms are at 15-3/8". I took a photo of it out in our warehouse, and while I wasn't able to get…
Hello Jeff, thanks for reaching out. Yes, the Caliber Vehicle Ramps with Wheel Chocks #CA24AJ can indeed support the front end of a 24K 38foot class a gasser. The ramps have a 20,000 lb capacity when used as a pair which will be more than enough for…
Hey Michael, for wet bolts you could use the part #126B2 and then for bronze bushings part #D014-077-00 but we do not have any brass bushings in the size you need. How many miles do you have on the Road Armor equalizers you think?
Hello Eulalio, thanks for reaching out. That truck is freaking nice looking! Good job! The Caliber Vehicle Ramps with Wheel Chocks #CA24AJ are 9" tall at the highest point. They will provide about 6-1/2" of lift off a level garage floor.
Thank you for providing that information. It sounds like you already know this, but you want to choose a replacement equalizer that closely matches the one that came with the trailer. Since you have an 8" measurement on your standard equalizers…
Hey Ronald, you actually don't need to use two sets of the Caliber Vehicle Ramps part #CA24AJ. You could just put them under the outside tires and they would work great. They have more than enough capacity at 20k since most your van would weigh…
The Replacement No-Drill Inflation Valve Bracket for Firestone Air Helper Springs Systems #F98ZR does not come with the cable ties you're looking for. Instead, you'll want to use the Replacement Inflation Valve Bracket for Firestone Air…
Hey Daniel, good question. This is normal for a torsion axle. You spinning the trailer 180 degrees is not going to damage the suspension. That is just how torsion axles work. As the wheels move the rubber inside the axle flexes, and that is what you…
Hey Steve, yes a Rock Tamers mud flap kit like the part #RT47VR would work with the Weigh Safe adjustable ball mounts part #WS68RR and #WS56ZR. The ball mounts have enough clearance on the shank to allow the Rock Tamers to fit.
The middle and rear jack mounting brackets of the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 6-Point Set #LC675817 that you referenced are a total of 6 inches in width. That's how much free room…
Yes, the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote #LC675817 which uses 6 points for leveling would fit and work well on your 2010 Keystone Montana fifth wheel. This would be an excellent way to keep your…
2-Ton vehicle jacks can be ratcheted up and down for easy height adjustment, making it easier to change your flat tire or to get up under your vehicle for minor repairs. Always use jack stands in pairs for safety.
Switch-operated jack has 18" of screw travel and a 4-1/2" drop leg. Retracted height is 9" and extended height is 27". 7-Way plug makes setup easy. Extends 6" in 29 seconds with 1,000 lbs of tongue weight.
Pull the side-facing plunger pin on this heavy-duty jack to release the drop leg. The durable jack screw offers increased strength- lifts up to 5 tons, and supports 6. Sidewind crank included.
Swing-up boat trailer jack is perfect for your small boat or jet ski trailer. 6" Caster swivels 360 degrees to make it easy to maneuver your trailer. Clear zinc finish fights rust and corrosion.
Drop-leg jack stabilizes your lightweight cargo or camper trailer. Weld the bracket onto your trailer, pull the pin to lower the drop leg, and pin in place. Sturdy steel construction is durable.
Eliminate the need for wood or cinderblocks when leveling your trailer. Camco's trailer tongue jack stand provides a sturdy platform that evenly distributes your trailer weight and prevents slipping. The UV-stabilized jack can support 5,000 lbs.
The hydraulic bottle jack lifts, holds, and locks vehicles in place without jack stands. Fitting unibody framed vehicles, the Unijack is perfect for cars, crossovers, and small SUVs and trucks. 18-3/8" Lift range with 2 ton capacity.
StayPut jack stand pad helps to distribute the weight of your jacks and stop them from sinking. EZ grip handle and handy storage strap. Lightweight and UV stabilized.
Replaces 1 pad for your SnapPad jack stand pad system. Pad increases the surface area of the jack foot to help prevent sinking and provides added stability. Fits 7" square jack foot.
Filters
