Keep your small boat centered during the loading process, despite wind and waves, with these bunk-board-style guide-ons. Corrosion-resistant guides are covered with marine-grade carpet and fit trailer frames up to 3" wide x 4-1/4" tall.The pre-galvanized steel support posts mount horizontally on top of or below your trailer's frame rail. Just slide the posts into the boat guide supports and secure the posts so that the distance between the bunks correctly matches the width of your boat. The bunk boards then tilt to conform to the boat's hull.
Bunk-board kit lets you build your own guide-ons to ease loading of your boat onto your trailer. Kit includes 90-degree-angled tubes, brackets, hardware, and enough marine-grade carpet for (2) 69" long 2x4 boards (not included).Features: Bunk-board kit lets you create 2 guide-ons to support your boat and keep it centered while you're loading it onto your trailer 2x4 Lumber for bunk boards not included 90-Degree-angled tubes let you mount the bunks close to your boat Great for narrow boats Bolt-on installation - clamp onto top or bottom of your trailer's frame Pre-galvanized steel construction is sturdy and corrosion-resistant Marine-grade carpeting lines bunk boards to protect your boat's finish 2 Rolls included to cover 2 boards U-bolts, brackets, and mounting hardware included Made in the USA Specs: Application: trailer frames up to 3" wide x 4-1/2" tall 2 Extra-long U-bolt kits (CE11416 - sold separately) are required to mount on frames up to 3" wide x 5-1/4" tall 2 Sets of I-beam clamps (CE27682A - sold separately) can be used to mount on I-beam frames that are larger than 3" wide x 4-1/4" tall Carpeting dimensions (per roll): 11" wide x 12' long Maximum 2x4 length for carpeting: 69" Pre-Galvanized Steel Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized.
Easily load your pontoon boat with these bunk-board-style guide-ons. The boards are covered with marine-grade carpet and their height can be adjusted during installation. Fits trailer frames up to 3" wide x 4-1/4" tall. ... The bunk-board-style guides will help to center your pontoon boat during loading and to support the boat during transport. Galvanized Steel Galvanized steel parts are hot-dipped in zinc after being stamped.
If your bow shifts off center during loading, it can contact the trailer. This 3-inch bow roller assembly cushions the bow and helps center the boat, with end bells for added protection so you can load with less contact.These 2' guide-ons use black carpeted 2x4 bunk boards to help guide the boat onto the trailer, giving the hull a defined path during loading and unloading.
Get better visibility for launching and loading your boat with these post extensions. Slide extensions into the top of your existing bunk-style guide-ons and secure with included hardware. Adjustable posts give you up to 37" of added height.Line up the mounting holes of the extension, guide-on, and bunk Insert the included mounting hardware into the mounting holes Tighten with a 9/16" wrench Repeat this process with the other guide-on, and you'll be ready to launch and load your boat with ease.
Keep your small boat centered during the loading process, despite wind and waves, with these bunk-board-style guide-ons. Corrosion-resistant guides are covered with marine-grade carpet and fit trailer frames up to 3" wide x 4-1/4" tall.The pre-galvanized steel support posts mount horizontally on top of or below your trailer's frame rail. Just slide the posts into the boat guide supports and secure the posts so that the distance between the bunks correctly matches the width of your boat. The bunk boards then tilt to conform to the boat's hull.
Hey Chris, thanks for reaching out, and nice boat! Based on what you are describing, I'd go with the bunk-style guide-ons. Since you usually aren't power loading, the bunks will help catch the hull and keep it centered. Plus, the bunks help…
For bunk style guide-ons such as #CE27600 the bunk board and boat should only barely touch if at all. There isn't a hard and fast rule that says it should be this many inches. But since guide-ons are not meant to support weight like a regular…
I spoke with my contact at CE Smith, and they said the Bolster and Swivel Bracket Assembly for Boat Trailers, part #CE10000G, do not bear the weight of the boat. The U-bolt that attaches the brackets to the trailer frame support the weight of the…
You will need to locate the safety chains before the cut that is made to install the Fold-Away Coupler Hinge, #FHDPB330301, to be in compliance with DOT regulations. Normally the chains are welded to the bottom or side of the trailer framing, and ran…
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…
Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…
It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…
Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…
A boat that refuses to slide is enough to ruin a good morning of fishing. Cutting drag with every launch, this low-maintenance bunk wrap lets your boat glide smoothly off and on your trailer, giving you more time on the water than at the ramp.It's a cleaner, lower-maintenance option made to hold up through years of loading and unloading. Plus, this kit comes with end caps. Not only will your bunks have a clean, seamless look, you won't have to deal with exposed carpet staples and they help prevent board rot. Installs Over Standard Bunk Boards You'll need to remove the carpet from your bunks before installing these wraps, but once they're on, you're done.
Give your trailer bunks a clean, finished look with this 4-pack of endcaps. Perfect for single-trailer installs or replacements. Designed for 2x4 boards and pairs with Caliber bunk wrap. ... Clean, Finished Look These molded endcaps cover the exposed ends of your bunks to prevent splintering and help seal out moisture. They pair perfectly with Caliber wrap and give your setup a smooth, professional-looking finish.
Give your trailer bunks a clean, finished look with this 4-pack of endcaps. Perfect for single-trailer installs or replacements. Designed for 2x4 boards and pairs with Caliber bunk wrap. ... Clean, Finished Look These molded endcaps cover the exposed ends of your bunks to prevent splintering and help seal out moisture. They pair perfectly with Caliber wrap and give your setup a smooth, professional-looking finish.
Give your trailer bunks a clean, finished look with this 4-pack of endcaps. Perfect for single-trailer installs or replacements. Designed for 2x6 boards and pairs with Caliber bunk wrap. ... Clean, Finished Look These molded endcaps cover the exposed ends of your bunks to prevent splintering and help seal out moisture. They pair perfectly with Caliber wrap and give your setup a smooth, professional-looking finish.
A boat that refuses to slide is enough to ruin a good morning of fishing. Cutting drag with every launch, this low-maintenance bunk wrap lets your boat glide smoothly off and on your trailer, giving you more time on the water than at the ramp.It's a cleaner, lower-maintenance option made to hold up through years of loading and unloading. Plus, this kit comes with end caps. Not only will your bunks have a clean, seamless look, you won't have to deal with exposed carpet staples and they help prevent board rot. Installs Over Standard Bunk Boards You'll need to remove the carpet from your bunks before installing these wraps, but once they're on, you're done.
Give your trailer bunks a clean, finished look with this 4-pack of endcaps. Perfect for single-trailer installs or replacements. Designed for 2x6 boards and pairs with Caliber bunk wrap. ... Clean, Finished Look These molded endcaps cover the exposed ends of your bunks to prevent splintering and help seal out moisture. They pair perfectly with Caliber wrap and give your setup a smooth, professional-looking finish.
A boat that refuses to slide is enough to ruin a good morning of fishing. Cutting drag with every launch, this low-maintenance bunk wrap lets your boat glide smoothly off and on your trailer, giving you more time on the water than at the ramp.It's a cleaner, lower-maintenance option made to hold up through years of loading and unloading. Plus, this kit comes with end caps. Not only will your bunks have a clean, seamless look, you won't have to deal with exposed carpet staples and they help prevent board rot. Installs Over Standard Bunk Boards You'll need to remove the carpet from your bunks before installing these wraps, but once they're on, you're done.
A boat that refuses to slide is enough to ruin a good morning of fishing. Cutting drag with every launch, this low-maintenance bunk wrap lets your boat glide smoothly off and on your trailer, giving you more time on the water than at the ramp.It's a cleaner, lower-maintenance option made to hold up through years of loading and unloading. Plus, this kit comes with end caps. Not only will your bunks have a clean, seamless look, you won't have to deal with exposed carpet staples and they help prevent board rot. Installs Over Standard Bunk Boards You'll need to remove the carpet from your bunks before installing these wraps, but once they're on, you're done.
Buying wrap by the roll? These 2x4 endcaps finish off your bunks with a clean look. Includes 24 black caps - great for trailer pros and marine shops handling multiple projects. Hardware not included.Highlights Designed for 2x4 Bunks: Caps fit standard trailer bunk boards for a finished look. Great for Bulk Projects: Includes 24 endcaps ideal for dealers and multi-trailer installs.
A boat that refuses to slide is enough to ruin a good morning of fishing. Cutting drag with every launch, this low-maintenance bunk wrap lets your boat glide smoothly off and on your trailer, giving you more time on the water than at the ramp.It's a cleaner, lower-maintenance option made to hold up through years of loading and unloading. Plus, this kit comes with end caps. Not only will your bunks have a clean, seamless look, you won't have to deal with exposed carpet staples and they help prevent board rot. Installs Over Standard Bunk Boards You'll need to remove the carpet from your bunks before installing these wraps, but once they're on, you're done.
A boat that refuses to slide is enough to ruin a good morning of fishing. Cutting drag with every launch, this low-maintenance bunk wrap lets your boat glide smoothly off and on your trailer, giving you more time on the water than at the ramp.It's a cleaner, lower-maintenance option made to hold up through years of loading and unloading. Plus, this kit comes with end caps. Not only will your bunks have a clean, seamless look, you won't have to deal with exposed carpet staples and they help prevent board rot. Installs Over Standard Bunk Boards You'll need to remove the carpet from your bunks before installing these wraps, but once they're on, you're done.
A boat that refuses to slide is enough to ruin a good morning of fishing. Cutting drag with every launch, this low-maintenance bunk wrap lets your boat glide smoothly off and on your trailer, giving you more time on the water than at the ramp.It's a cleaner, lower-maintenance option made to hold up through years of loading and unloading. Plus, this kit comes with end caps. Not only will your bunks have a clean, seamless look, you won't have to deal with exposed carpet staples and they help prevent board rot. Installs Over Standard Bunk Boards You'll need to remove the carpet from your bunks before installing these wraps, but once they're on, you're done.
Buying wrap by the roll? These 2x6 endcaps finish off your bunks with a clean look. Includes 24 black caps - great for trailer pros and marine shops handling multiple projects. Hardware not included.Highlights Designed for 2x6 Bunks: Caps fit standard 2x6 trailer bunk boards for a finished look. Great for Bulk Projects: Includes 24 endcaps ideal for dealers and multi-trailer installs.
Working on multiple trailers? This wrap cuts drag at the ramp so your boats glide on and off with less effort. And with 250' to work with, you'll have plenty of wrap for large-scale projects or for stocking your boat supply store.Helps Your Boat Slide On Easier This wrap's slick surface reduces friction, so instead of cranking your boat off sticky bunks, your boat will glide on and off the trailer with less effort. That means less strain on your ropes, pulleys, bow eyes, and your arms!
A boat that refuses to slide is enough to ruin a good morning of fishing. Cutting drag with every launch, this low-maintenance bunk wrap lets your boat glide smoothly off and on your trailer, giving you more time on the water than at the ramp.It's a cleaner, lower-maintenance option made to hold up through years of loading and unloading. Plus, this kit comes with end caps. Not only will your bunks have a clean, seamless look, you won't have to deal with exposed carpet staples and they help prevent board rot. Installs Over Standard Bunk Boards You'll need to remove the carpet from your bunks before installing these wraps, but once they're on, you're done.
Working on multiple trailers? This wrap cuts drag at the ramp so your boats glide on and off with less effort. And with 250' to work with, you'll have plenty of wrap for large-scale projects or for stocking your boat supply store.Helps Your Boat Slide On Easier This wrap's slick surface reduces friction, so instead of cranking your boat off sticky bunks, your boat will glide on and off the trailer with less effort. That means less strain on your ropes, pulleys, bow eyes, and your arms!
Buying wrap by the roll? These 2x4 endcaps finish off your bunks with a clean look. Includes 24 light gray caps - great for trailer pros and marine shops handling multiple projects. Hardware not included.Highlights Designed for 2x4 Bunks: Caps fit standard trailer bunk boards for a finished look. Great for Bulk Projects: Includes 24 endcaps ideal for dealers and multi-trailer installs.
Buying wrap by the roll? These 2x6 endcaps finish off your bunks with a clean look. Includes 24 light gray caps - great for trailer pros and marine shops handling multiple projects. Hardware not included.Highlights Designed for 2x6 Bunks: Caps fit standard 2x6 trailer bunk boards for a finished look. Great for Bulk Projects: Includes 24 endcaps ideal for dealers and multi-trailer installs.
Filters
