You hook up your dump trailer, try to run the hydraulics, and nothing happens. The battery's dead. This charger lets you plug into shore power to keep your trailer battery charged between jobs.
You can stick the control knob to the dashboard, plug in the module, and your brake controller installation is done with no drilling and no hardwiring. The knob is large and easy to use, while the main unit is out of sight behind the dash.If a harness is unavailable for your vehicle, hardwiring will be necessary. If you don't already have a 7-wayplug at the back of your vehicle, take a look at our exclusive 7- and 4-way brake control installation kit (ETBC7 - sold separately.
Electric A-frame jack has 2 toggle switches for operation. Jack has a retracted height of 9", an extended height of 28-1/2", and 19-1/2" of travel. Drop leg offers an extra 5-5/8" of lift. 7-way RV-style plug makes setup easy.Features: Electric jack lets you raise and lower your A-frame trailer Drop leg allows for increased lift and saves time when raising or lowering Pin and clip holds leg at desired location 2 Toggle switches on the front of the housing let you operate the jack On/off switch controls light Extend/retract switch controls up and down movement 7-way RV-style plug pulls power from your vehicle's trailer connector No need to manually wire for power 7-Way must have active 12 volt pin LED light illuminates at a downward angle to help you focus on your coupler Emergency crank (included) allows you to manually operate jack if needed Black powder coated outer tube Zinc-finished inner tube and footplate resist corrosion Simple, bolt-on installation Specs: Bracket height: Retracted: 9" Extended: 28-1/2" Total lift: 25-1/8" Screw travel: 19-1/2" Drop leg travel: 5-5/8" Clearance: 20-1/2" From bottom of bracket to top of jack Outer tube diameter: 2-1/4" Inner tube diameter: 2" Hole spacing on drop leg: 1-7/8" Footplate diameter: 5-1/2" Lift capacity: 3,500 lbs 1-Year warranty How to Determine the Lift Capacity You Need in a Jack A trailer jack is designed to lift the tongue of your trailer so you can connect the trailer coupler to your hitch ball.
You can stick the control knob to the dashboard, plug in the module, and your brake controller installation is done with no drilling and no hardwiring. The knob is large and easy to use, while the main unit is out of sight behind the dash.Once you're plugged into the factory port, just plug the other end of the adapter into the main unit. No hardwiring needed! Note: If you don't already have a 7-wayplug at the back of your vehicle, take a look at our exclusive 7- and 4-way brake controller installation kit (ETBC7 - sold separately).
Replaces the electric steps, motor, and control unit for your Kwikee 25 series RV steps. Motor and control unit automatically extend and retract the steps when you open and close your door. Wiring pigtail hardwires to your RV's power.The complete assembly with steps, motor, control unit, and switch kit is available under part number LC3658373 . The included 4-wayplug fits into the existing wiring harness on your RV. Most vehicles should having this wiring already set up. In the event that your RV is missing the wiring, a 4-way pigtail is included to help you hardwire the unit to your RV.
Replaces the electric steps, motor, and switch kit for your Kwikee 32 series RV steps. Motor extends and retracts the steps when it receives the signal from the switch kit. Wiring pigtail hardwires to your RV's power.The complete assembly with steps, motor, control unit, and switch kit is available under part number LC372261 . The included 4-wayplug fits into the existing wiring harness on your RV. Most vehicles should have this wiring already set up. In the event that your RV is missing the wiring, a 4-way pigtail is included to help you hardwire the unit to your RV.
Replaces the electric steps, motor, and control unit for your Kwikee 27 series RV steps. Motor and control unit automatically extend and retract the steps when you open and close your door. Wiring pigtail hardwires to your RV's power.If you want the complete step assembly that also allows you to override the automatic retraction so the steps stay out whether the door is open or closed, you will need a switch kit (sold separately). The included 4-wayplug fits into the existing wiring harness on your RV. Most vehicles should having this wiring already set up. In the event that your RV is missing the wiring, a 4-way pigtail is included to help you hardwire the unit to your RV.
Replaces the electric steps, motor, and control unit for your Kwikee 47 series RV steps. Motor and control unit automatically extend and retract the steps when you open and close the door. Wiring pigtail hardwires to your RV's power.If you want the complete step assembly that also allows you to override the automatic retraction so the steps stay out whether the door is open or closed, you will need a switch kit (sold separately). The included 4-wayplug fits into the existing wiring harness on your RV. Most vehicles should having this wiring already set up. In the event that your RV is missing the wiring, a 4-way pigtail is included to help you hardwire the unit to your RV.
Replaces the electric steps, motor, and control unit for your Kwikee 25 series RV steps. Motor and control unit automatically extend and retract the steps when you open and close your door. Wiring pigtail hardwires to your RV's power.The complete assembly with steps, motor, control unit, and switch kit is available under part number LC3658373 . The included 4-wayplug fits into the existing wiring harness on your RV. Most vehicles should having this wiring already set up. In the event that your RV is missing the wiring, a 4-way pigtail is included to help you hardwire the unit to your RV.
Replaces the electric steps, motor, and control unit for your Kwikee Platinum series RV step. Motor and control unit automatically extend and retract the steps when you open and close the door. Wiring pigtail hardwires to your RV's power.If you want the complete step assembly that also allows you to override the automatic retraction so the steps stay out whether the door is open or closed, you will need a switch kit (sold separately). The 4-wayplug (sold separately) fits into the existing wiring harness on your RV. Most vehicles should having this wiring already set up.
You can stick the control knob to the dashboard, plug in the module, and your brake controller installation is done with no drilling and no hardwiring. The knob is large and easy to use, while the main unit is out of sight behind the dash.Once you're plugged into the factory port, just plug the other end of the adapter into the main unit. No hardwiring needed! Note: If you don't already have a 7-wayplug at the back of your vehicle, take a look at our exclusive 7- and 4-way brake controller installation kit (ETBC7 - sold separately).
Replaces the electric step, motor, and control unit for your Kwikee 28 series RV step. Motor and control unit automatically extend and retract the step when you open and close your door. Wiring pigtail hardwires to your RV's power.The complete assembly with steps, motor, control unit, and switch kit is available under part number LC3747453 . The included 4-wayplug fits into the existing wiring harness on your RV. Most vehicles should having this wiring already set up. In the event that your RV is missing the wiring, a 4-way pigtail is included to help you hardwire the unit to your RV.
Replaces the electric steps, motor, and control unit for your Kwikee 42 series RV steps. Motor and control unit automatically extend and retract the steps when you open and close your door. Wiring pigtail hardwires to your RV's power.If you want the complete step assembly that also allows you to override the automatic retraction so the steps stay out whether the door is open or closed, you will need a switch kit (sold separately). The included 4-wayplug fits into the existing wiring harness on your RV. Most vehicles should having this wiring already set up. In the event that your RV is missing the wiring, a 4-way pigtail is included to help you hardwire the unit to your RV.
You can stick the control knob to the dashboard, plug in the module, and your brake controller installation is done with no drilling and no hardwiring. The knob is large and easy to use, while the main unit is out of sight behind the dash.Once you're plugged into the factory port, just plug the other end of the adapter into the main unit. No hardwiring needed! Note: If you don't already have a 7-wayplug at the back of your vehicle, take a look at our exclusive 7- and 4-way brake controller installation kit (ETBC7 - sold separately).
Electric step assembly includes everything you need to automatically open and close the steps with your RV door. Motor and control unit extend and retract steps. Switch kit overrides step retraction. Amber light illuminates when steps extend.The included 4-wayplug fits into the existing wiring harness on your RV. Most vehicles should have this wiring already set up. In the even that your RV is missing the wiring, a 4-way pigtail is included to help you hardwire the unit to your RV.
You can stick the control knob to the dashboard, plug in the module, and your brake controller installation is done with no drilling and no hardwiring. The knob is large and easy to use, while the main unit is out of sight behind the dash.Once you're plugged into your factory port, just plug the other end of the adapter into the main unit. No hardwiring needed! Note: If you don't already have a 7-wayplug at the back of your vehicle, take a look at our exclusive 7- and 4-way brake controller installation kit (ETBC7 - sold separately).
Replaces the electric steps, motor, and control unit for your Kwikee 24 series RV step. Motor and control unit automatically extend and retract the steps when you open and close the door. Wiring pigtail hardwires to your RV's power.If you want the complete step assembly that also allows you to override the automatic retraction so the steps stay out whether the door is open or closed, you will need a switch kit (sold separately). The included 4-wayplug fits into the existing wiring harness on your RV. Most vehicles should having this wiring already set up. In the event that your RV is missing the wiring, a 4-way pigtail is included to help you hardwire the unit to your RV.
You can stick the control knob to the dashboard, plug in the module, and your brake controller installation is done with no drilling and no hardwiring. The knob is large and easy to use, while the main unit is out of sight behind the dash.Once you're plugged into the factory port, just plug the other end of the adapter into the main unit. No hardwiring needed! Note: If you don't already have a 7-wayplug at the back of your vehicle, take a look at our exclusive 7- and 4-way brake controller installation kit (ETBC7 - sold separately).
Get a head-start on wiring your towed car before you even get the installation started. This kit comes with butt connectors pre-installed and ready to splice into your wiring. Integrated block diodes protect your vehicle from electrical feedback.Features: Connects your RV's tail, brake, and turn signal lights to your towed car's tail lights Plugs into your motorhome with 4-way flat connector Splices quickly into car's electrical system with included butt connectors Color-coded wires with wiring guide makes installation easier Prevents feedback that can damage your vehicle's electrical components with integrated block diodes Includes 4-wire harness, 4-flat extension cable, mounting bracket, silicone sealant, zip-ties, and installation hardware 1-Year limited warranty Do I Need a Brake Light Relay?
Mount this 7-way connector in your aluminum truck bed for quick, simple hookup of your 5th-wheel or gooseneck trailer. Custom harness plugs in-line with your existing factory wiring so that you can retain use of your vehicle's factory 7-pole.
Replaces the electric step, motor, and switch kit for your Kwikee 26 series RV steps. Motor extends and retracts the step when it receives the signal from the switch kit. Wiring pigtail hardwires to your RV's power.The complete assembly with steps, motor, control unit, and switch kit is available under part number LC3711363 . The included 4-wayplug fits into the existing wiring harness on your RV. Most vehicles should have this wiring already set up. In the event that your RV is missing the wiring, a 4-way pigtail is included to help you hardwire the unit to your RV.
Replaces the electric steps and motor that work with your existing Kwikee control unit and switch kit. Control unit (sold separately) or switch kit (sold separately) is required for operation.The complete assembly with steps, motor, control unit, and switch kit is available under part number LC372261 . The included 4-wayplug fits into the existing wiring harness on your RV. Most vehicles should having this wiring already set up. In the event that your RV is missing the wiring, a 4-way pigtail is included to help you hardwire the unit to your RV.
Filters
