Result: fasteners

LED Utility Light - 6 Diode - Sealed - 3inch Round - Clear w/ Chrome Snap-On Trim Ring # UCL60CB - Seems just what I need -but how do I secure it? Due to security, I do not like pressed grommet.. Really want a bolted/screwed stainless bezel/ring,...

Can this light be grounded another way to a boat trailer as opposed to via the mounting fastener to the trailer only? This specific light looks like the best candidate for several replacement lights needed on my trailer but Im not sure I want...

What fasteners do I need to hold the license plate holder in place. I have a trailer bumper that Im mounting this to, it is 10.36mm thick and 5mm diameter hole. I have a picture for reference as well but from some reason I cannot attach pictures...

Hi, I was wondering what size of fasteners are required for the LP31CB lights. Do you have any license plate lights that use #10 and have the ground built in, so no extra lead for the ground? | At most you would use 1/4 inch screws with license...

I have the old style wesbar tail lights on my Trail Master trailer. The bolts that hold them on to the frame have round heads that are hidden under the waterproof protector. When I try to loosen the nuts,they just spin and there is no way to...

Is there anything that will secure the ground wire to the metal on a trailer to ensure the ground wire will stay in contact with the trailer? Or is it best to just drill a hole in the metal and secure the ground wire by placing a screw through...

I am replacing two small side marker lights on a Shorelandr ATV trailer. The existing lights mount in holes in the square tube sides, and there is no way to use a screw and nut. It looks like there are nylon push fasteners holding the light...

I have a question about LP81BB. What is the size fastener needed for this part to mount? | I went out into our warehouse and measured the install holes of the Ear Mount, Plastic Trailer License Plate Light # LP81BB and found them to be 3/16...

How do these get mounted on a trailer? Is there a mounting box needed to fasten to trailer? | The clearance and side marker light you referenced, part # AL82AB, uses a plastic mounting base that is sold separately. The base is available...

I need a small spring that goes on the outside heater vent door.i tried a spring from a pen and its to skinny. The size of the spring that I lost was about 3/4 long and 1/4 wide.if you dont have one only in a 3 piece kit thats OK to | Hey Joe,...

Wired as a reverse tail light on a trailer. Light flashes on for a split second as the vehicle is shifted into reverse but then immediately turns off when reverse is fully engaged. Need help! | Since the Optronics Utility Light # UCL60CB is...

I thought that your website would surely have locking t handles, like I have on the back door of my pickup canopy, and my chicken coup, but I can’t find them. Mine are fastened to the canopy door with two bolts, 1.5 inch centers. | Yes, we...

What is the recommended mounting hardware for this reflector? Also, how thick is it? | The screw hole of the Optronics Trailer Reflector, # RE35RB, is 1/4 inch in diameter. There is also a small lip that is 3/8 of an inch in diameter (see photo)....

Hello, I would like to know the size of the fasteners included with this light kit. Thread and pitch ie 1/4 - 20 unc and length. Thanks for your help. Regards, | I would love to help but unfortunately Optronics was not able to provide...

I am looking a replacement light for an old ambulance. It is an amber sidemarker or clearance light. It appears to be approx 4x2 inches in size and is flat. It has a Phillips screw exposed on each end that fastens the light to the side of the...

I just watched your video on installing light base MCL75RB. It showed using rivets not screws, it did not say if you could use aluminum or you needed stainless steele. Can I use aluminum and if so what size? Thank you | The mounting hole...

There are no bolts or boalt holes on these lights to fassen them to your mount??? How do you fasten them to you exsiting mounts?? | I went out to the warehouse and pulled Optronics Trailer Light, # ST45RB. First, you will need to place the Rubber...

On the product description for BK70BB, a reviewer installed this on a Thule easy-fold ET bike rack. His photos show clamps under the rack used to hold the wire inside the loom. Do you sell the clamps/fasteners as well or have a suggestion...

Hi...I have a Joe Hauler motorcycle carrier. Ive looked through all your lighting kit pages without much success. Can you please recommend a brake/taillight kit that would mount onto the back of the carrier without drilling into the square...

installed these brackets with self drilling stainless steel hex head screws but the led lamps will not fit due to the height of the screw heads. What is the proper way to fasten the bracket A67BB? Also what do I do with the white ground wire...

Is there a bracket available for light ILL28CMB? I need to mount this overhead in the cargo box of a straight truck. Ive seen a bracket that has a lip that goes between the roof bows and the fiberglass top. This bracket also has a cutout that...

I am trying to wire a back up camera and dont want to splice the wiring. There are several kits that would T the connection...I need both +12, ground, and back up lights for the camera...I am not sure which kit to buy. Also on the other end...

Can I mount E98943 to a trailer hitch bike rack and will 98174LED mount in E98943 securely and not fall out? Will light # 98174LED fit into Bracket # BK70BB is there a screw fastener to hold the light in the bracket or what will keep it from...

Looking for a set of reflectors just like these for my F150 mud flaps but I I am limited to a 10W . . . cannot do 12W. I dont want to do 2 4 1/2inch on each flap . . . I want to keep it at 1 piece. Been looking for a year. THX | If...