!mercury  x   >   !1974  x   >   !Sonoma Travel Trailer  x   >   Gen-Y Hitch  x   >  

Hi I am looking for a 2x2 ball mount, preferably shock absorbing, with 0 rise that can support a boat and trailer at 7,500lbs. I saw the post asking for this but the recommendation was for a 6k lbs ball mount. Any advice? Thanks | I have two...

Hello, I bought a tow hitch from etrailer a few years back and it is rated for 10,000 lbs 5 inch . I have a dump trailer Big Tex that weighs 4K lbs and is rated to haul 14K lbs. I also tow a camper which is about 10K lbs. So, I see that you...

Is this hitch a good safe solution for a 2020 Ford Expedition Plat pulling 5k/7.5k trailers? Trying to get a full list of premium parts to use for long term towing on a 2020 ford expedition platinum w/ heavy tow pkg 9200 rated tow, 1700lb payload....

will this adapter fit a potomac 5231 fith wheel? also how tall is it. my truck is a 94 dodge 2500 with 4 inch lift kit. the previous adapter I got is too tall to work. | If the current pin box on your Potomac 5231 5th wheel trailer has a Lippert...

so what do these light weight inch rams weigh ? | The 14' long Gen-Y Hitch Aluminum Loading Ramp Set # GH34FR have a shipping weight of 188 lbs so when you take into consideration the shipping materials, these aluminum ramps are going to weigh...

will this work with standard ball mount? i have a 2 inch receiver on my suv. i need a 5-6 inch drop for my trailer5000lbs and would like to use and accessory above that. thank you, also, if this would work would you have it available without...

I own a Grand Design 295RL fifth wheel with a Turning Point pin box. I would like to replace the Turning Point with either the Reese Goosebox or the Gen-Y executive. I can find no signage on either the wings or the pin box to indicate fitment...

I know it says 3inch of rise and 9inch of drop but I need more rise. Can I flip this over to get 9 inch of rise? | Yes, the Gen-Y Torsion 2-Ball Mount w/ Stacked Receivers # 325-GH-1325 can be used in the rise and drop position. So you'd be...

Hello I was trying to find out which gen-y fifth wheel pin box replacement with gooseneck coupler hitch I need to order for my 2014 Dutchman voltage v3895 fifth wheel trailer | In order to find out which Gen-Y Hitch Shock Absorbing 5th Wheel...

I pull a 21’ trailer that has 4400 lbs empty weight and 480 lbs of tongue weight . I need about two to three inch I won’t know exactly until spring.i would like a cushion hitch. Is the shocker impact right for us? Is there enough tongue Wieght...

is there anything more reliable than the clip provided | If you're looking for something different than the Replacement Pin and Clip # AM3430 from Anderson then you might try out the Gen-Y Hitch Pin and Clip # 325-GH-096 which has similar dimensions...

What is the thickness in inches of the hooked ends that attach to trailer deck? | The hooked ends of the Gen-Y Hitch Aluminum Loading Ramps # GH34FR are going to be 3/8" thick. This ramp set will hold up to 8000-lbs total (4000-lbs per ramp)...

I see the 7 inch extender which will probably work for me. I really only need 4 - 6. Are there shorter ones available less than 7? Thanks, | The Brophy 7" Hitch Extender for 2" Hitch Receivers # HE06 is the shortest hitch extender that's...

Will this work with a 2011 RAM 3500 with a CM flatbed with the recessed ball? | Yes, you can use the Gen-Y Hitch Shock Absorbing 5th Wheel-Gooseneck Pin Box # GY36FR with your 2011 Ram 3500 and CM flatbed with recessed gooseneck ball. You will...

WILL THESE RAMPS CARRY MY F250 DIESEL,FOUR DOOR, SHORT BOX PICKUP.PROBABLY WONT LOAD THIS MUCH BUT JUST IN CASE.mAINLY MY MODELA and 39 ford sedan.Thanks | I did some research and your truck may weigh anywhere from just under 5,600 lbs to 6,182...

Hi there, if not i tended to use to the max capacity more on the flexibility of the tubes, can be mounted with only bottom spacers? The frame on my truck tapers have a small dovetail witch will impede the use of the top spacers, thanks | When...

I’m interested in trying the used Gen-Y Part Number 325-GH-12001 for use on my small aluminum cargo trailer. It is a Thule Cargopro 2000 which has a lower tongue weight- would this still help? It is a single axle and does clunk around quite...

I have a 2019 Chev Silverado 2500 and will tow a trailer weighing 8800 pounds using cruisenaster DO45 coupling. If you could confirm which of the GenY hitches and accessories is appropriate for my set up that would be great. Regards | It...

I have a 2022 f350 , 6.75’ box ,2022 5th wheel Jayco camper, rhino box, 12995lb gvwr, will the gen y hitch work ? | The Gen-Y Hitch 5th Wheel to Gooseneck Pin Boxes like part # GY98GR are designed for long bed trucks. That said, there are many...

I have a winch which is bolted onto a winch receiver hitch,unfortunately I do not have the mounts part #. I would like to pull a car onto my open trailer using this winch ..the trailer does not have a spot for a winch,or I try and bolt it onwhich...

i want a hitch extension for my GMC 3500 dually, 2022. I have just put a new Lance 1172 truck Camper on it. What type of hitch extension do you recommend for pulling a boat that would weigh with boat, motor and trailer about 2500- 3000 lbs?...

looking to purchase a Blue Ox Hitch Receiver Immobilizer II - 2inch Hitches Item # BX88224 to use with PH54FR patriot hitches which i will also purchase if it will work with my Subaru Ascent factory mounted hitch which is located in the bumper....

What is the maximum tongue weight allowed. My current BandW is only 1,000lbs. | 1,000 lbs is the maximum tongue weight of the B&W Tow & Stow 3-Ball Mount item # BWTS10049C. It's the same on the rest of the B&W tow and stow's for a 2" hitch receiver....

If a ball is not needed, but a lower ride height is desired, could an accessory like the Yakima OnRamp Bike Rack for 2 Electric Bikes - 2inch Hitches - Frame Mount Item # Y36FR be used with the Phantom Hitch? | To lower the ride height for...