Keel Roller and Wobble Roller Capacities to Consider when Setting Up a Boat Trailer
I have two questions.First I would like some info on how to setup a trailer as far as the proper keel contact versus outside bottom roller contact.My next question is can I install end caps with the same length roller shaft that comes with a...
Will Yates 5 Inch Wobble Roller Fit a 1991 EZ Loader Boat Trailer
Will these fit a 1991 Ez loader roller trailer? | Most of the boat trailer rollers that we carry, including # YR530R-8P, are not trailer specific. You would go by the measurements of the roller. This wobble roller has a 5 inch diameter and is...
Availability Of Boat Trailer Roller Made Of Non-Marring Material
Are these rollers available in non-marking materials | I may have another option for you, but there is nothing like the Yates Side Guide Roller for Boat Trailers - Heavy-Duty Rubber - 12" Long - 5/8" Shaft # YR12243-5 you were looking at available...
How Much Roller Shaft Length will Yates Endcap for Side Guide Rollers # YR224-4 End Up Taking up
how much additional shaft length is needed for using roller end caps | I went out and pulled a Yates Endcap for Side Guide Rollers # YR224-4 from our warehouse to measure it and found that it is going to take up 1-3/8 inch of roller shaft space. |
Where to Measure to Pick Out Replacement Rollers for a Boat Trailer
I am looking for a roller for my 1982 Calkins boat trailer. I think it is model #21-6400. I am pretty sure about the numbers except the number 1 in the model number. S/N may be 2123 2002. Not 100 sure. Can you help? Thank you , | We carry...
Does the Yates Ribbed Wobble Roller 4-3/8" Diameter - 5/8" Shaft Need a Bushing
My trailer roller shaft measures at 5/8 . I see you sell a 5/8th inner diameter roller. I assume the rollers dont need bushings ? | The Yates Ribbed Wobble Roller 4-3/8" Diameter - 5/8" Shaft does not require a bushing, it's designed to slip...
Shaft with Caps and Mounting Bracket Recommendation for the Yates Keel Roller # YR18244-165EC
Do you have a matching end cap for this roller? If so which shaft will accommodate the complete combination of the 18inch roller and the caps? | The recommended shaft for with the Yates Rubber Boat Trailer Parts # YR18244-165EC that you referenced...
Is it Advisable to Change Diameter of Wobble Rollers
I have an older Shoreline roller trailer. I am trying to replace the wobble rollers on it as one fell off and the others are showing some wear. The thing is, I am seeing two potentially 3 different overall sizes as I measure the ones on...
Availability of 5 Inch Long Keel Roller for 1/2 Inch Diameter Shaft
I am looking for both an 8inch keel roller and a 5inch mid roller for a boat trailer I am fixing up. I need each roller with a 1/2inch ID and all I have found are rollers with 5/8inch ID - if you have ANY 8inch and 5inch rollers with a 1/2inch...
Wobble Roller Recommendation for a Boat Trailer that Fits 7/8 inch Roller Shaft
I have a very old 1974 ez loader trailer. The shaft is 7/8inch by my measurement. This model says it is for a 1inch shaft and the center hole measures 1 and 1/16. Which would be 1/4inch larger than my 4/8inch shaft. Will this product work...
Comparing 8" Long Yates Keel Rollers for Boat Trailer
compare center groove on Yates 8244 vs y 8000 8inch roller. the 8244 seems a lot more narrow as compared to the y 8000 need to replace on a Shorelander trailer with a 3 1/2inch end dia. org. is a yates but seems to have a wider center...
Keel Roller Needed 12 Inches Long With 5/8 Inch Shaft To Center Boat
Price and availability for your #YR87169? I enter this number in your search and come up with nothing. | The reason why you can't find the Husky Self-Centering Keel Roller - Polyvinyl - 12" Long - 5/8" Shaft - Black, YR87169 is because it has...
Bow Roller Recommendation Near 4 inches in Width
I am looking for a 4inch non marker bow roller that is as close to 4 inch wide as possible like 3.875 wide with as large bell diameters as possible. What is available? | For bow rollers we have 4 inch wide rollers like the part # YR450Y-400Y...
Will The Keel Pads Mount To 2x4 Bunk Boards On a Boat Trailer?
Can I use them on a 2x4 on bunks. | The Yates Keel Pad # YR1203SB is designed to fit on 3" wide frames and crossmembers. To mount them on bunk boards you would have to notch the 2"x4" for them to even fit. Also the pad is not designed to hold...
Is the Yates Ribbed Wobble Roller # YR500YW-8PEZ Sold Individually
How many rollers are in this? | The Yates Ribbed Wobble Roller # YR500YW-8PEZ that you referenced is a single roller sold individually. |
Tool Recommendation for Installing Retainer Ring for Wobble Rollers
To install a CE10987 retainer ring for a Yates343R-6P, is there a tool available? | Sounds like you are looking for a way to secure the # CE10981 to the shaft for the installation of the part # YR343R-6P. A decent set of pliers like the part...
What is Diameter is the Center Hole for Yates Boat Trailer Roller # YR4163-4P
This 4inch yates roller with 1/2inch shaft appears to have an in the center hole or roller shaft hole for the 1/2inch shaft to slip into. Is that correct for this roller. My existing rollers have a 1/2inch shaft and so I wanted to make sure...
Replacement Boat Trailer Wobble Roller Installation
I need to replace a wobble roller has a split,how do I do this and do I need washers for both ends,mine has a cotter pin | The boat trailer replacement wobble rollers we offer include both black rubber and non-marking thermoplastic types that...
Shaft Recommendation for Use with Yates 8 inch Spool Roller
Dont see a 1/2 inch roller shaft and pal nuts for your 8inch spool roller YR8302-4P. Am I missing something or do I buy a extra long one and cut it off? Thanks | The shaft you would want to use with the 8 inch long spool roller part # YR8302-4P...
Bow Roller Recommendation for a Trailer with a 3-5/8 Inch Wide Bracket
Bracket at front of trailer is 3 5/8 wide. Right between sizes for your bow rollers - guess I need the three inch but that leaves quite a bit of gap, so wonder if I get the 4 inch model - which might not exactly measure 4 inches? Your help...
Keel Roller Center Diameter Dimension of # YR1200Y
I would like to know the diameter of the keel roller in the very center, where the keel would ride. I have limited clearance in this area after the installation of the Keel Guard protector and now my original black rubber roller will not fit....
Determining The Correct Replacement Keel Roller For 2018 Tige RZX3
I am looking for a keel roller replacement for a 2018 Tige RZX3, it’s a 23ft pickle fork wakeboard boat | I would be happy to help you find the correct replacement keel roller for your 2018 Tige RZX3, but you will need to measure the length...
Custom Lawn Roller Compatibility Using Boat Rollers To Be Used Behind Mower
I am going to use your roller in an off label application. I plan to use several of these for the purpose of a lawn roller behind my mower deck. My question is do you have a product that would be more ideally suited for this application or a...
Replacement Bow Roller Bracket, Shaft and Roller
So I have an old boat trailer I need to change the bow rollers on but the shafts are larger than 1/2 in. Theyre about 3/4. I cant find anything anywhere with anything bigger than 1/2 in. | We don't have any bow rollers that will fit a roller...
Filter Your Search
Contact and Help