Bow Roller Recommendation for a Trailer with a 3-5/8 Inch Wide Bracket
Published 09/22/2014
Products Featured in This Question
Question:
Bracket at front of trailer is 3 5/8 wide. Right between sizes for your bow rollers - guess I need the three inch but that leaves quite a bit of gap, so wonder if I get the 4 inch model - which might not exactly measure 4 inches? Your help would be greatly appreciated. Thanks
asked by: Kenneth S
0
Expert Reply:
You would want to go with the 3 inch Yates Bow Roller for Boat Trailers # YR300Y. This would fit well on your bracket that is 3-5/8 inches with only a little over a 1/4 of an inch of gap on either side of the roller.
A 4 inch roller would be too wide and wouldn't fit.
expert reply by:
Jameson C
0
click to enlarge
Product Page this Question was Asked From
Yates Bow Roller for Boat Trailers - TPR - 4" Long - 1/2" Shaft - Yellow
- Boat Trailer Parts
- Rollers
- Bow Roller
- 3-1/4 Inch Diameter
- Plastic
- 3-3/4 Inch Long
- Fits 1/2 Inch Shaft
- Yates Rubber
more information >
Continue Researching
- Search Results: coupler pin
- Search Results: 1/2 pin
- Search Results: bow roller
- Search Results: grease packer
- Search Results: hitch coupler pin
- Search Results: cap nuts
- Search Results: trailer leaf springs
- Shop: CE Smith U-Bolt Kit for Mounting 2" Square Trailer Axles - 4-1/2" Long U-Bolts - Zinc
- Shop: Dexter Trailer Hub and Drum Assembly for 3,500-lb Axles - 5 on 4-1/2 - Galvanized
- Shop: CE Smith Shackle Bolts with Lock Nuts - 3-1/2" Long - Qty 2
- Shop: etrailer Rust-Resistant 4-Leaf Slipper Spring for 4,300-lb Trailer Axles - 26-1/4" - Dacromet
- Shop: Karrier ST215/75R14 Radial Trailer Tire with 14" Galvanized Wheel - 5 on 4-1/2 - Load Range C
- Shop: Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel (Pair)
- Shop: Dexter Nev-R-Adjust Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
- Video: The Low-Down on the CE Smith Bow Roller Assembly with Bells for 4" Wide Bracket
- Video: Comprehensive Review: Bearing Packer
- Video: etrailer Rust-Resistant 4-Leaf Slipper Spring for 4,300-lb Trailer Axles Review
- Video: A Closer Look at the Coupler Pin
- Video: Let’s Check Out the Demco Channel Tongue Trailer Coupler
- Video: Let’s Check Out the CE Smith Bow Roller Assembly with Bells for 4" Wide Bracket
- Video: Feature Review Replacement Cap Nut
- Q&A: Recommended Wood for Bunk Boards on Boat Trailer
- Q&A: Is Junction Box Recommended When Installing New Trailer Wiring 7-Way
- Q&A: Does the Dutton-Lainson 14627 Mount Using Existing Shelby 5407B Bolt Pattern
- Q&A: Does a Trailer Junction Box Have to be Used when Switching from 4-Way to 7-Way Trailer Connector
- Q&A: Do I Need to Have a Castle Nut or Cotter Pin to Keep Spindle Nut From Backing Off
- Q&A: When do You Need a Breakaway Battery Charger and How Does it Function
- Q&A: When Would a Trailer Break Away Kit Be Required By Law